« previous next »
Pages: [1] 2

Author Topic: Temp Nocks  (Read 2286 times)

0 Members and 1 Guest are viewing this topic.

Offline DC

  • Member
  • Posts: 10,396
Temp Nocks
« on: September 23, 2019, 01:43:37 pm »
Has anyone had any failures just CA gluing a wedge to the back of a bow for a temp nock? I'm a little concerned with just pulling on the glue line. Like this mock up only with a little better joint ;D ;D
Logged

Offline PEARL DRUMS

  • Member
  • Posts: 14,079
  • }}}--CK-->
Re: Temp Nocks
« Reply #1 on: September 23, 2019, 01:49:45 pm »
I never use temp string grooves on any bow. I put over lays on as soon as the bow is off the floor.
Logged
Only when the last tree has died and the last river has been poisoned and the last fish has been caught will we realize we cannot eat money.

Offline DC

  • Member
  • Posts: 10,396
Re: Temp Nocks
« Reply #2 on: September 23, 2019, 01:55:49 pm »
But that involves making a decision early in the process ;D ;D, I guess they're easy enough to change though. Do you use wide overlays and then narrow them along with the tips?
Logged

Offline PEARL DRUMS

  • Member
  • Posts: 14,079
  • }}}--CK-->
Re: Temp Nocks
« Reply #3 on: September 23, 2019, 02:00:27 pm »
Nope. I make them to size right away and just touch them up with a sanding block at the end. Any string alignment issues can easily be take care during tillering if you keep an eye out for it. I've never been one to use tip width to adjust tracking and I've always chosen a top and bottom limb right from the start and never sway from it. I have never ran into issues with either scenario I couldn't work through. Just have to think 3 steps ahead at all times. No surprises.
Logged
Only when the last tree has died and the last river has been poisoned and the last fish has been caught will we realize we cannot eat money.

Offline DC

  • Member
  • Posts: 10,396
Re: Temp Nocks
« Reply #4 on: September 23, 2019, 02:02:58 pm »
'Three' steps? I've been having trouble with one ;D ;D Thanks for the response.
Logged

Offline PEARL DRUMS

  • Member
  • Posts: 14,079
  • }}}--CK-->
Re: Temp Nocks
« Reply #5 on: September 23, 2019, 02:04:19 pm »
Most of what I do is contrary to common building practices. Not sure why, just how my mind works I guess.
Logged
Only when the last tree has died and the last river has been poisoned and the last fish has been caught will we realize we cannot eat money.

Offline Del the cat

  • Member
  • Posts: 8,322
    • Derek Hutchison Native Wood Self Bows
Re: Temp Nocks
« Reply #6 on: September 23, 2019, 02:37:16 pm »
No....
Del
Logged
Health warning, these posts may contain traces of nut.

Offline Stickhead

  • Administrator
  • Member
  • Posts: 940
Re: Temp Nocks
« Reply #7 on: September 23, 2019, 03:12:06 pm »
I prefer to leave the tips a little extra wide so I can cut in temp nocks.  Then I narrow them near the final tillering stages and add overlays (or not) and final cuts.
Logged

Offline SLIMBOB

  • Member
  • Posts: 3,759
  • Deplorable Slim
Re: Temp Nocks
« Reply #8 on: September 23, 2019, 09:57:21 pm »
I use jute twine and CA glue. Heat gun releases it. I don’t use them much, but need to from time to time.
Logged
Liberty, In God We Trust, E Pluribus Unum.  Distinctly American Values.

bownarra

  • Guest
Re: Temp Nocks
« Reply #9 on: September 24, 2019, 12:31:05 am »
CA by itself will fail sometimes/most times.
I use a bit of B50 to whip mine on after gluing them with just a spot or two of glue. This way you can cut the B%00 off then easily pop off the temp. overlay.
I do this on just about every bow I make. I prefer to cut my nock grooves in when the tip is at finished size. I don't try to correct tip alignment this way I follow the grain always its just nice to have a fresh tip to work on when it comes time for the nocks.
Logged

Offline leonwood

  • Member
  • Posts: 762
    • Leonwood Bows
Re: Temp Nocks
« Reply #10 on: September 24, 2019, 08:47:53 am »
I always glue on temp nocks with CA. I even boil them while recurving and I have never had one come off
Logged

Offline Pat B

  • Administrator
  • Member
  • Posts: 37,633
Re: Temp Nocks
« Reply #11 on: September 24, 2019, 09:03:17 am »
I wouldn't trust those wedges just glued on. A sinew or thread wrap over the wedge maybe. I do as Stickhead does and leave the tips wide with side nocks just deep enough for the string. If everything is good I reduce the tips to final shape, add overlays and cut in the final string grooves.
Logged
Make the most of all that comes and the least of all that goes!    Pat Brennan  Brevard, NC

Offline DC

  • Member
  • Posts: 10,396
Re: Temp Nocks
« Reply #12 on: September 24, 2019, 10:21:51 am »
I compromised a bit and cut a notch out. This way the string isn't pulling right on the glue line but it's easy to get the string off for tillering close to the ends. I've had good luck with CA for tips. Never had one pop off. I have lost them through steaming or fuming though.
Logged

Offline Weylin

  • Member
  • Posts: 2,296
Re: Temp Nocks
« Reply #13 on: September 24, 2019, 02:01:14 pm »
I mostly do like Pearly and get the tips like I want them early. When I have done temporary nocks I used scraps of osage and just cut a groove over the top like I would on a nicer overlay, making sure to go perpendicular to the grain. I leave them hanging off the tip of the bow a bit and when i'm done with them I pop them off and save them for another time.
Logged

Offline kbear

  • Member
  • Posts: 157
Re: Temp Nocks
« Reply #14 on: September 24, 2019, 05:00:10 pm »
Good topic. I have been putting my overlays on as soon as floor tiller is done also. I've been wondering if it is the right thing to do. I've decided if Pearly and Weylin do it...... it can't be wrong!
Logged
Pages: [1] 2
« previous next »