« previous next »
Pages: [1] 2 3

Author Topic: static recurve help  (Read 8715 times)

0 Members and 1 Guest are viewing this topic.

Offline dylanholderman

  • Member
  • Posts: 787
static recurve help
« on: July 15, 2018, 07:35:44 pm »
so yesterday i bent the recuves on this osage stave first one went fine barely any cracking, second one though  :( i had a crack/wind shake open up on it. i knew it was there before bending it and was planning on filling it with CA glue after i bent it but with how wide the crack opened to on the back i'm not sure now. thoughts?  ???


Logged

Offline upstatenybowyer

  • Member
  • Posts: 2,700
Re: static recurve help
« Reply #1 on: July 15, 2018, 07:40:17 pm »
Fill w/ CA and slap an "underlay" on there?  :-\

It's worked for me in very similar situations.

Best of luck!  )P(
Logged
"Even as the archer loves the arrow that flies, so too he loves the bow that remains constant in his hands."

Nigerian Proverb

Offline Danzn Bar

  • Member
  • Posts: 4,166
Re: static recurve help
« Reply #2 on: July 15, 2018, 07:45:18 pm »
Is that some sapwood on the back?
How thick is it in the bend?
Does the crack go through the limb?
DBar
Logged
Integrity is doing the right thing when no one is looking

Offline dylanholderman

  • Member
  • Posts: 787
Re: static recurve help
« Reply #3 on: July 15, 2018, 08:53:31 pm »
yes there's one ring of sapwood i left on it for looks
its maybe 9/16-5/8 of a inch thick at the moment in hind sight i should have brought it closer to 1/2 inch
and yes the crack go's all the way through it but not any farther down the limb
Logged

Offline Pat B

  • Administrator
  • Member
  • Posts: 37,633
Re: static recurve help
« Reply #4 on: July 15, 2018, 09:20:04 pm »
Dylan, I agree with upstate. Fill it with super glue. You mar eliminate it or most of it when you thin the tips. If not add an underlay(overlay) and it should be OK.
Logged
Make the most of all that comes and the least of all that goes!    Pat Brennan  Brevard, NC

Offline bjrogg

  • Member
  • Posts: 11,016
  • Cedar Pond
Re: static recurve help
« Reply #5 on: July 16, 2018, 04:59:06 am »
My gut tells me it'll work. But I think I'd give it a wrap of sinew. It's hard to tell but looks like it maybe goes out end of bow? Maybe that's a pencil mark. It seems like a static should be ok.
Bjrogg
Logged
A hot cup of coffee and a beautiful sunrise

Offline Aaron H

  • Member
  • Posts: 3,437
Re: static recurve help
« Reply #6 on: July 16, 2018, 06:03:22 am »
Another vote for underlay / overlay
Logged

Offline Eric Krewson

  • Member
  • Posts: 5,432
Re: static recurve help
« Reply #7 on: July 16, 2018, 08:02:46 am »
Overlays can be very attractive, I have cracked statics bending them and put overlays on all the curves  to make up wood after for filing the cracks out and over thinning the limbs.

Logged

Offline upstatenybowyer

  • Member
  • Posts: 2,700
Re: static recurve help
« Reply #8 on: July 16, 2018, 08:18:23 am »
That does look nice Eric  :OK
Logged
"Even as the archer loves the arrow that flies, so too he loves the bow that remains constant in his hands."

Nigerian Proverb

Offline Danzn Bar

  • Member
  • Posts: 4,166
Re: static recurve help
« Reply #9 on: July 16, 2018, 11:08:36 am »
I would thin the tips, with that large of a crack I would use epoxy to fill and add overlays to both the back and belly side of the tips.  Epoxy fills voids much better than super glue.   Super glue is best for thin cracks JMO
DBar
Logged
Integrity is doing the right thing when no one is looking

Offline dylanholderman

  • Member
  • Posts: 787
Re: static recurve help
« Reply #10 on: July 16, 2018, 01:44:29 pm »
What about a foaming style glue  ??? I’ve misplaced my CA but I have a bottle of foaming polyurethane glue and some 5min epoxy
Logged

Offline aaron

  • Member
  • Posts: 1,037
Re: static recurve help
« Reply #11 on: July 16, 2018, 01:53:01 pm »
No to the foaming glue. 5 min epoxy is not as good as a longer cure epoxy. If possible, get the best glue for the job. Either good superglue like loctite 420 or gorilla. Or a good epoxy that cures in 24 hrs. Personally i would use epoxy if the crack is wide.
Logged
Ilwaco, Washington, USA
"Good wood makes great bows, but bad wood makes great bowyers"

Offline Pat B

  • Administrator
  • Member
  • Posts: 37,633
Re: static recurve help
« Reply #12 on: July 16, 2018, 04:45:45 pm »
Thin super glue would be best because it will get down into the small cracks. Time to get a new bottle of super glue.
Logged
Make the most of all that comes and the least of all that goes!    Pat Brennan  Brevard, NC

Offline dylanholderman

  • Member
  • Posts: 787
Re: static recurve help
« Reply #13 on: July 16, 2018, 08:20:20 pm »
alright i'll run by the hardware store and get some more CA (i think i might have left my old one up at Marshall  :()
i'll also thin the tip down some and see if putting a clamp on the tip might close up the crack some.
Logged

Offline PatM

  • Member
  • Posts: 6,737
Re: static recurve help
« Reply #14 on: July 16, 2018, 09:28:40 pm »
Looks like the crack goes right through. I would do what DBar suggests.  Epoxy will flow into thin cracks if you warm it.    Tape off  the belly side and pour it in the top.  After it cures flatten and double up the overlays on back and belly.
Logged
Pages: [1] 2 3
« previous next »