Author Topic: hickory hole  (Read 1561 times)

0 Members and 1 Guest are viewing this topic.

Offline trail walker

  • Member
  • Posts: 77
hickory hole
« on: November 27, 2017, 06:18:29 pm »
So i had a little bug hole on my hickory board stave, i am planing on trying to sinew back this bow with 1 1/2 layers wondering if you guy thin the hole will will hurt it. the hole is at the tip of the pencil in the full picture.

Offline trail walker

  • Member
  • Posts: 77
Re: hickory hole
« Reply #1 on: November 27, 2017, 06:21:43 pm »
sorry it is kinda hard to see the bottom one. the hole is like 2 inches above the handle.

Offline Eric Krewson

  • Member
  • Posts: 5,346
Re: hickory hole
« Reply #2 on: November 27, 2017, 07:03:02 pm »
You may get lucky but that is a powder post beetle hole. The last hickory I tried with a few of the those benign looking holes blew up on me.

Here is what the do under the surface of the wood that you can't see;


Offline trail walker

  • Member
  • Posts: 77
Re: hickory hole
« Reply #3 on: November 27, 2017, 09:25:18 pm »
well then. :P. what if i wrapped that area with sinew to. All i need is like 20 inches of draw at 60 lbs. I don't know that that would even makes a difference? I am trying to get proficient with a Native American short draw style, so i don't need tons of length on the draw.

Offline willie

  • Member
  • Posts: 3,197
Re: hickory hole
« Reply #4 on: November 27, 2017, 09:36:28 pm »
can you tell how long the hole is ?  is the bottom pic supposed to show the other end of the hole?

Offline trail walker

  • Member
  • Posts: 77
Re: hickory hole
« Reply #5 on: November 27, 2017, 10:10:17 pm »
no there is only one hole, i do not know how deep it goes. i was showing where on the hole was on the bow.

Offline Hamish

  • Member
  • Posts: 1,498
Re: hickory hole
« Reply #6 on: November 28, 2017, 04:17:51 am »
Use a pin as a depth gauge to see how deep the hole is.

Offline Pappy

  • Global Moderator
  • Member
  • Posts: 31,901
  • if you have to ask you wouldn't understand ,Tenn.
Re: hickory hole
« Reply #7 on: November 28, 2017, 05:40:00 am »
Like Eric said, the hole isn't a problem, what you can't see very well could be. It is one of them things that if you are willing to take the chance just go for it. For me I am not willing and use it as fire wood.  :)
 Pappy
Clarksville,Tennessee
TwinOaks Bowhunters
Life is Good

Offline JW_Halverson

  • Member
  • Posts: 11,881
Re: hickory hole
« Reply #8 on: November 28, 2017, 11:31:11 am »
It's perfect just the way it is....for smoking meats.

Those beetles do not always bore straight lines.  Dribbling glue and stuffing a thin plug in the hole might just solv the cosmetics while internally the time bomb tick...tick...ticks away.

How bad do you need this to be a bow?  If it is just another bow, go for it with the understanding that it is likely a failure in the making. If you NEED a bow, you NEED better wood.
Guns have triggers. Bicycles have wheels. Trees and bows have wooden limbs.

Offline DC

  • Member
  • Posts: 10,396
Re: hickory hole
« Reply #9 on: November 28, 2017, 11:44:29 am »
How about a narrower bow? Just trim away at that edge and see if the hole disappears. If it turns and goes sideways, junk it.

Offline Eric Krewson

  • Member
  • Posts: 5,346
Re: hickory hole
« Reply #10 on: November 29, 2017, 06:53:53 am »
I found a picture of my hickory bow failure because of powder post beetles. If you look in the middle of the picture you can see segmented bug do-do where the beetle trail turned up the limb.

This was a rather spectacular failure;


Offline ohma2

  • Member
  • Posts: 960
Re: hickory hole
« Reply #11 on: November 29, 2017, 03:55:31 pm »
HEED the picture.