« previous next »
Pages: [1]

Author Topic: Tip overlay question  (Read 2251 times)

0 Members and 1 Guest are viewing this topic.

Offline Spotted Dog

  • Member
  • Posts: 700
Tip overlay question
« on: March 11, 2016, 11:55:25 am »
when I get to the point , what glue is best for tip overlays. Horn and or wood ?

Dog
« Last Edit: March 11, 2016, 12:05:24 pm by Spotted Dog »
Logged
A three strand cord is not easily broken. Ecc.4:12

Offline bigcountry

  • Member
  • Posts: 841
Re: Tip overlay question
« Reply #1 on: March 11, 2016, 12:01:48 pm »
I use titebond 3.  Make sure both surfaces are real smooth.  I have also used loktite superglue on horns with great success.
Logged
Westminster, MD

Offline dylanholderman

  • Member
  • Posts: 787
Re: Tip overlay question
« Reply #2 on: March 11, 2016, 12:04:16 pm »
Super glue is my go to glue for tip overlays
Logged

Offline bubby

  • Member
  • Posts: 11,054
Re: Tip overlay question
« Reply #3 on: March 11, 2016, 12:08:20 pm »
Loktight professional super glue
Logged
failure is an option, everyone fails, it's how you handle it that matters.
The few the proud the 27🏹

Offline ajooter

  • Member
  • Posts: 1,234
Re: Tip overlay question
« Reply #4 on: March 11, 2016, 12:11:50 pm »
If it's antler I saturate the bottom with super glue to fill all voids, sand it lightly smooth,  then use either super glue or a two part epoxy.  For wood I use tb2 or 3.

Just gotta make sure your surfaces are good and flush.   I usually end up using the overlay with a piece of heavy sandpaper underneath foe the final fitting.
Logged

Offline osage outlaw

  • Member
  • Posts: 11,962
Re: Tip overlay question
« Reply #5 on: March 11, 2016, 12:25:45 pm »
I always use super glue.  Like everyone else mentioned, get the surfaces perfectly flat and matching.  I clean both surfaces with acetone or alcohol and let them dry before gluing them.
Logged
I started out with nothin' and I still got most of it left

Offline TimothyR

  • Member
  • Posts: 658
  • PM110782
Re: Tip overlay question
« Reply #6 on: March 11, 2016, 12:32:54 pm »
Super glue. I use the krazy kind. But I'm a little krazy!! :P
Logged
Freedom dies one compromise at a time. III%

Offline Spotted Dog

  • Member
  • Posts: 700
Re: Tip overlay question
« Reply #7 on: March 11, 2016, 12:43:03 pm »
Tim I am going to use some of that red wood I got from you.
Thanks guys. I wanted to be sure. Grateful.
Logged
A three strand cord is not easily broken. Ecc.4:12

Offline Pat B

  • Administrator
  • Member
  • Posts: 37,633
Re: Tip overlay question
« Reply #8 on: March 11, 2016, 01:09:07 pm »
I've used super glue, both gel and thin, TBI, TBII, TBIII and 2ton epoxy, all with good success. Surface pre is the critical part of it.
Logged
Make the most of all that comes and the least of all that goes!    Pat Brennan  Brevard, NC

Offline chamookman

  • Member
  • Posts: 3,026
Re: Tip overlay question
« Reply #9 on: March 12, 2016, 03:29:39 am »
I'm with Pat, 'cept You forgot the Resorcinal  >:D :laugh: :laugh:! Bob
Logged
"May the Gods give Us the strength to draw the string to the cheek, the arrow to the barb and loose the flying shaft, so long as life may last." Saxon Pope - 1923.
Pages: [1]
« previous next »