« previous next »
Pages: [1]

Author Topic: Butt splice hickory bow lives. Picture on tiller tree. Advice needed  (Read 3059 times)

0 Members and 1 Guest are viewing this topic.

Offline make-n-break

  • Member
  • Posts: 378
Butt splice hickory bow lives. Picture on tiller tree. Advice needed
« on: March 06, 2016, 09:09:51 pm »
Well. It lives at 45@28"... It's currently 66" ttt with temp knocks tied on. I exercised it 200 times at final tiller just to make sure it didn't pop.  It took 1" set on bottom limb and 1-3/8 on top, but the top limb started with about 1/4 inch of deflex. All of the sisal is temporary.

I need to get the weight up. 45 is too light for me. I would like at least 50 but no more than 55 for longevity of my ghetto splice. What do you guys recommend...

-Pike one inch off each end making it 64"?

-a thorough heat treating?

The handle looks ugly as sin with those dowels haha!! Went with 3/16 lam over that mess of a butt splice as a couple fellas recommended.  Thankful for all your wisdom and thankful it's alive so far.
« Last Edit: March 06, 2016, 09:27:29 pm by make-n-break »
Logged
"When making a bow from board staves you are freeing a thing of dignity from the humiliation of static servitude." -TBB1

Offline Drewster

  • Member
  • Posts: 687
Re: Butt splice hickory bow lives. Picture on tiller tree. Advice needed
« Reply #1 on: March 06, 2016, 09:20:08 pm »
Your tiller looks great.  Before I shortened it any at all, I would heat treat.  That should get you five pounds.  Based on the pic, it looks like your ntn is about 64" or 65".  If your draw is 28", I would leave the length alone.  Just my 2¢.
Logged
Drew - Boone, NC

Offline BowEd

  • Member
  • Posts: 9,390
  • BowEd
Re: Butt splice hickory bow lives. Picture on tiller tree. Advice needed
« Reply #2 on: March 06, 2016, 09:50:46 pm »
Yep good advice.You could easily pick up 6 to 8 pounds from a heat treatment and a little reflex.Do it evenly on both limbs though.Don't want to change that good tiller.Congrats.
I always got more faith in sinew myself for wrapping.
Logged
BowEd
You got to stand for something or you'll fall for anything.
Ed

Offline George Tsoukalas

  • Member
  • Posts: 9,425
    • Traditional and Primitive Archers
Re: Butt splice hickory bow lives. Picture on tiller tree. Advice needed
« Reply #3 on: March 06, 2016, 10:00:53 pm »
Looks to me that tiller is pretty darn good but I don't think there any inches left for the draw length. In other words, it is maxed out. Shortening the bow will not help.
Start another bow.
Jawge
Logged
Set Happens!
If you ain't breakin' you ain't makin!

Offline Onebowonder

  • Member
  • Posts: 1,495
Re: Butt splice hickory bow lives. Picture on tiller tree. Advice needed
« Reply #4 on: March 07, 2016, 11:00:29 am »
I love the band you have achieved with this bow!  I'm very glad your cover-up lam worked out well.

Do you have a good reflex caul?  If not, they are pretty easy to build.  I think you could Steam (...careful not to steam the handle) or just use a heat gun to put this bow into a bit of reflex, (...maybe an inch and a half or two) and then heat treat the SNOT out of the belly.  The limbs are hickory, so I'd seal them up right after heat treatment while still hot and then leave it on the caul for extra time to cool down completely.  That should get you the extra pounds you need.

Don't worry about the looks of the handle.  You can cover the whole thing with a nice leather grip if you like and it'll disappear completely. :)

OneBow
Logged

Offline Chief RID

  • Member
  • Posts: 684
Re: Butt splice hickory bow lives. Picture on tiller tree. Advice needed
« Reply #5 on: March 07, 2016, 12:42:30 pm »
Unbelievable MNB. Absolutely a lesson in woodworking. Thanks for taking us along.
Logged

Offline Del the cat

  • Member
  • Posts: 8,322
    • Derek Hutchison Native Wood Self Bows
Re: Butt splice hickory bow lives. Picture on tiller tree. Advice needed
« Reply #6 on: March 07, 2016, 01:01:12 pm »
Nice looking bend  :)
Del
Logged
Health warning, these posts may contain traces of nut.

Offline paco664

  • Member
  • Posts: 307
  • ok,ok.. i might have done it...
Re: Butt splice hickory bow lives. Picture on tiller tree. Advice needed
« Reply #7 on: March 07, 2016, 02:01:25 pm »
sweet... hell.. you say the handle is ugly... i'd shoot it and be proud of it...
Logged
I'm too drunk to taste this chicken"~Col.H.Sanders

Offline joachimM

  • Member
  • Posts: 675
  • Good - better - broken
Re: Butt splice hickory bow lives. Picture on tiller tree. Advice needed
« Reply #8 on: March 07, 2016, 05:11:51 pm »
In order to gain draw weight by piking you'd need to shorten 2" at each end to get to 55#, just a tad over 1" to get to 50". Heat seems best to me too. And I actually like that handle, with the pegs and all.

Logged

Offline Stick Bender

  • Member
  • Posts: 2,003
Re: Butt splice hickory bow lives. Picture on tiller tree. Advice needed
« Reply #9 on: March 07, 2016, 05:45:34 pm »
I really like the handle too I think the end grain on the dowels against the long grain on the handle if oiled or stained will really pop off  glad to see it survive & thrive ! 
Logged
If you fear failure you will never Try !

Offline make-n-break

  • Member
  • Posts: 378
Re: Butt splice hickory bow lives. Picture on tiller tree. Advice needed
« Reply #10 on: March 08, 2016, 09:04:06 am »
Thanks everyone. I don't have a reflex form OneBow. I took the advice and gave it a good deep heat treating but kept the straight profile. No piking. I'll touch up the tiller in the next couple days, finish it out and hopefully get some completion pics up this weekend. I'm really hoping everything holds with the new weight gain! I'd love to take a turkey with this one in a couple weeks. I modified my tillering tree with an extra long rope when this project started lol.
Logged
"When making a bow from board staves you are freeing a thing of dignity from the humiliation of static servitude." -TBB1

Offline sleek

  • Member
  • Posts: 6,764
Re: Butt splice hickory bow lives. Picture on tiller tree. Advice needed
« Reply #11 on: March 08, 2016, 09:07:11 am »
Gluing that piece on the back is certainly what saved it. That looks nice especially with the handle wrap.
Logged
Tread softly and carry a bent stick.

Dont seek your happiness through the approval of others

Offline make-n-break

  • Member
  • Posts: 378
Re: Butt splice hickory bow lives. Picture on tiller tree. Advice needed
« Reply #12 on: March 08, 2016, 09:54:05 am »
Thanks sleek. I'll get a proper one on there while finishing. That one was just a temp to see what it looked like and lessen the shrapnel during an explosion.
Logged
"When making a bow from board staves you are freeing a thing of dignity from the humiliation of static servitude." -TBB1

Offline sleek

  • Member
  • Posts: 6,764
Re: Butt splice hickory bow lives. Picture on tiller tree. Advice needed
« Reply #13 on: March 08, 2016, 10:00:38 am »
I doubt it will explode. If it fails it will begin to pull apart and you will notice that, if it happens. I think the odds are good for you though. I would soak the handle wrap in glue when you re do it. 
Logged
Tread softly and carry a bent stick.

Dont seek your happiness through the approval of others

Offline Springbuck

  • Member
  • Posts: 1,545
Re: Butt splice hickory bow lives. Picture on tiller tree. Advice needed
« Reply #14 on: March 09, 2016, 02:11:13 pm »
Heat treat it back to straight if you can, and flip the tips just an inch or so about 5" or 6 " from the end. In my experience, if you don't go overboard, this will give you the draw weight you need with almost no need to retiller anything.

Putting a full length reflex in is great, too.
Logged
Pages: [1]
« previous next »