« previous next »
Pages: [1] 2

Author Topic: Building some bamboo arrows. (finished! )  (Read 5841 times)

0 Members and 1 Guest are viewing this topic.

Offline Rob W.

  • Member
  • Posts: 77
Building some bamboo arrows. (finished! )
« on: February 07, 2016, 04:41:03 pm »
I found some good looking garden stakes at Menards so I bought all that looked like they would fly. Out of 24 so far I have 7 that are within 32 gr. of each other. A few where heavy and a few light. I think I culled 7 for various problems.

These 7 spine very similar and I should finish them this week. I broke one at the nock node during straightening so I built an osage nock for it. 520 gr. Avg without feathers, broadhead or hardwood insert. I hope to use these in my 67# osage this year.





« Last Edit: February 12, 2016, 03:26:24 pm by Rob W. »
Logged

Offline Pat B

  • Administrator
  • Member
  • Posts: 37,633
Re: Building some bamboo arrows.
« Reply #1 on: February 07, 2016, 05:35:45 pm »
Good start so far. Are you determining the stiff side of the arrow when setting the nocks? The still side should go against the bow.
Logged
Make the most of all that comes and the least of all that goes!    Pat Brennan  Brevard, NC

Offline Rob W.

  • Member
  • Posts: 77
Re: Building some bamboo arrows.
« Reply #2 on: February 07, 2016, 05:42:44 pm »
Yeah Pat I marked stiff side as I spined them and cut nocks accordingly. All in this weight group spined really close. I will spine again before I fletch to make sure of where I want the cock feather.

This stuff is way heavier than my river cane.
Logged

Offline Knoll

  • Member
  • Posts: 3,016
  • Mikey
Re: Building some bamboo arrows.
« Reply #3 on: February 07, 2016, 07:02:52 pm »
Fine looking osage nock!!
Logged
... alone in distant woods or fields, in unpretending sproutlands or pastures tracked by rabbits, even in a bleak and, to most, cheerless day .... .  I suppose that this value, in my case, is equivalent to what others get by churchgoing & prayer.  Hank Thoreau, 1857

Offline Trapper Rob

  • Member
  • Posts: 3,719
Re: Building some bamboo arrows.
« Reply #4 on: February 07, 2016, 08:38:01 pm »
Did you turn the nock on a lathe it looks good.
Logged

Offline Rob W.

  • Member
  • Posts: 77
Re: Building some bamboo arrows.
« Reply #5 on: February 07, 2016, 09:01:07 pm »
Rob, I cut a little piece of osage down with a pocket knife then chucked it up in a drill and smoothed it out. I may end up doing all my hunting arrows that way. I like the look better but it took me a lot longer to do.

I'm thinking about osage fore shafts.
Logged

Offline Rob W.

  • Member
  • Posts: 77
Re: Building some bamboo arrows.
« Reply #6 on: February 12, 2016, 03:25:39 pm »
I've got three done so far. They shoot really well. 30.75" between 680gr.  - 705gr. With 160 head. Should be the ticket for Wapiti!



Logged

Offline Rob W.

  • Member
  • Posts: 77
Re: Building some bamboo arrows. (finished! )
« Reply #7 on: February 12, 2016, 03:30:15 pm »
I really appreciate all the build alongs and questions answered here. This site is a wealth of info. 

I think I could have built 2 bows in the time it took me to build these arrows though.    ;D
« Last Edit: February 12, 2016, 03:34:40 pm by Rob W. »
Logged

Offline perry f.

  • Member
  • Posts: 20
Re: Building some bamboo arrows. (finished! )
« Reply #8 on: February 12, 2016, 04:26:39 pm »
Awesome looking arrows Rob. Can't wait to chase elk with them this fall........ Now I need to get a couple self bows done and some arrows to match to complete our journey.
Logged

Offline loon

  • Member
  • Posts: 1,307
Re: Building some bamboo arrows. (finished! )
« Reply #9 on: February 12, 2016, 05:33:41 pm »
Niice. Can't wait to build some. If my money order works out.

That bow looks awesome.

So if the shaft is weak when pressure is applied on one side, and stiff on the other, the side on which it bends less (stiffer) when applied the same pressure should go against the bow? So it acts stiffer than otherwise? What if the stiff side is "perpendicular" to the nocking point, would that allow arrows to be nocked either way?

Maybe I should dye bars on my white fletchings. They look great

Wonder where I could find sinew for cheap

Need to make an arrow straightening tool, a spine measurer, and a tillering tree.
« Last Edit: February 12, 2016, 06:32:02 pm by loon »
Logged

Offline Lumberman

  • Member
  • Posts: 335
Re: Building some bamboo arrows. (finished! )
« Reply #10 on: February 12, 2016, 05:49:27 pm »
Great looking arrows!
Logged

Offline Dakota Kid

  • Member
  • Posts: 897
  • Maker of Things
Re: Building some bamboo arrows. (finished! )
« Reply #11 on: February 12, 2016, 06:43:34 pm »
Quote from: loon on February 12, 2016, 05:33:41 pm


Wonder where I could find sinew for cheap



Roadkill.
Logged
I have nothing but scorn for all weird ideas other than my own.
~Terrance McKenna

Offline Knoll

  • Member
  • Posts: 3,016
  • Mikey
Re: Building some bamboo arrows. (finished! )
« Reply #12 on: February 12, 2016, 07:03:12 pm »
Good lookin' arrows. Congrats!
Logged
... alone in distant woods or fields, in unpretending sproutlands or pastures tracked by rabbits, even in a bleak and, to most, cheerless day .... .  I suppose that this value, in my case, is equivalent to what others get by churchgoing & prayer.  Hank Thoreau, 1857

Offline Danzn Bar

  • Member
  • Posts: 4,166
Re: Building some bamboo arrows. (finished! )
« Reply #13 on: February 12, 2016, 07:47:25 pm »
Mighty fine looking hunting arrows right there........
DBar
Logged
Integrity is doing the right thing when no one is looking

Offline Rob W.

  • Member
  • Posts: 77
Re: Building some bamboo arrows. (finished! )
« Reply #14 on: February 12, 2016, 08:08:25 pm »
Loon, I'm no expert but you should be able to get by with moving around the stiff side of cane/bamboo to suit a certain bow setup. For wood arrows I always make sure I cross cut the grain with the nock. That said I would rather just have stiff side against bow and adjust spine with arrow length or head weight on either material.
Logged
Pages: [1] 2
« previous next »