« previous next »
Pages: [1] 2

Author Topic: No set tiller  (Read 5280 times)

0 Members and 1 Guest are viewing this topic.

Offline DC

  • Member
  • Posts: 10,396
No set tiller
« on: October 28, 2014, 03:32:42 pm »
 When I'm trying no set tiller I'm supposed to pull to, say 16" and note the draw weight. Then pull an inch past that and then drop back to 16" and again note the draw weight. If it's less than the first time the bow is starting to take set. Then I'm supposed to stop and figure out what is causing the set.    What am I looking for? If it's 40# the first time and 38# the second time will there be a noticeable bend/hinge somewhere? What if the bend looks even, what else could it be? I'm a bit puzzled here.
Thanks
Don
Logged

Offline mhof86

  • Member
  • Posts: 125
Re: No set tiller
« Reply #1 on: October 28, 2014, 03:49:05 pm »
I am sure someone with more experience can help better than I but I will take a shot at it. When tillering for myself I will draw until one of three things happen:

1. I hit my target weight.
2. I hit my target draw length (hopefully at my target weight).
3. The most common durring the tillering process, I see a flaw. Either a flat spot, hinge, or one limb bending more than the other.

If you are drawing and not noticing any problem areas try taking a picture of the tiller. It will allow you to take a closer look without leaving the bow under stress.

There is also a tool you can make out of a block of wood (I haven't made one yet and the name escapes me) but you can use it to run on the belly of the bow to help point out flat spots... Please someone help  me out here with this one.

All of my bows so far have taken some set but not enough that I notice it on the tillering tree as I go. For me I notice it after I get to full draw and shoot it a few times. I try to go just over my target weight off the tree, so after shooting in and figuring a bit of set and loss of draw weight.

I hope some of this makes sense and that my method is not way off base.
Logged

Offline PEARL DRUMS

  • Member
  • Posts: 14,079
  • }}}--CK-->
Re: No set tiller
« Reply #2 on: October 28, 2014, 04:07:22 pm »
Low set tillering, not no set. That's impossible to pull off on a self bow.

Don I wouldn't play the game if I were you. Just build your bow the way you know how.
Logged
Only when the last tree has died and the last river has been poisoned and the last fish has been caught will we realize we cannot eat money.

Offline wizardgoat

  • Member
  • Posts: 2,397
Re: No set tiller
« Reply #3 on: October 28, 2014, 04:14:00 pm »
maybe wood isnt 100% dry?
Logged

Offline H Rhodes

  • Member
  • Posts: 2,172
Re: No set tiller
« Reply #4 on: October 28, 2014, 04:15:09 pm »
Yep, keeping set to a minimum is a good goal, but you are gonna get some.
Logged
Howard
Gautier, Mississippi

Offline DC

  • Member
  • Posts: 10,396
Re: No set tiller
« Reply #5 on: October 28, 2014, 04:36:16 pm »
Over thinking again, aren't I? :-[ :-[
Logged

Offline PEARL DRUMS

  • Member
  • Posts: 14,079
  • }}}--CK-->
Re: No set tiller
« Reply #6 on: October 28, 2014, 04:38:37 pm »
Big time
Logged
Only when the last tree has died and the last river has been poisoned and the last fish has been caught will we realize we cannot eat money.

Offline DC

  • Member
  • Posts: 10,396
Re: No set tiller
« Reply #7 on: October 28, 2014, 04:42:09 pm »
Quote from: wizardgoat on October 28, 2014, 04:14:00 pm
maybe wood isnt 100% dry?
I live on the Island, nothing is ever 100% dry ;D
Logged

Offline PEARL DRUMS

  • Member
  • Posts: 14,079
  • }}}--CK-->
Re: No set tiller
« Reply #8 on: October 28, 2014, 04:49:41 pm »
My suggestion to LOW set tillering. Get your bow bending perfectly on the floor at about 12-18# heavy. Brace it very low and finish tillering the extra weight off. You'll take on very, very little set if the bow is laid out properly for the species used.
Logged
Only when the last tree has died and the last river has been poisoned and the last fish has been caught will we realize we cannot eat money.

Offline Danzn Bar

  • Member
  • Posts: 4,166
Re: No set tiller
« Reply #9 on: October 28, 2014, 08:35:09 pm »
Quote from: PEARL DRUMS on October 28, 2014, 04:49:41 pm
My suggestion to LOW set tillering. Get your bow bending perfectly on the floor at about 12-18# heavy. Brace it very low and finish tillering the extra weight off. You'll take on very, very little set if the bow is laid out properly for the species used.

Excellent advice......I can believe it!
DBar
Logged
Integrity is doing the right thing when no one is looking

Offline Badger

  • Member
  • Posts: 8,124
Re: No set tiller
« Reply #10 on: October 29, 2014, 12:07:36 am »
  DC, if the bow starts to drop a little late in the tiller say around 24" and the drops are small don't worry about it, thats about the best you can do. If the bow starts to drop early at 18" draw you need to find out why. Moisture? Not enough working limb? Bow is too narrow to for the draw weight expected? uneven tiller. No set tillering is the goal but you will seldom ever hit it. When you do it is fantasitc but don't be disappointed if you don't I seldom get past 24" without some loss starting to take place.
Logged

Offline jeffp51

  • Member
  • Posts: 1,641
Re: No set tiller
« Reply #11 on: October 29, 2014, 12:09:14 am »
The tool mentioned above is called a tillering gizmo, and there is a how-to on how to make one elsewhere on this site.  I think it is a sticky in the how to section.  Here is the link:   http://www.primitivearcher.com/smf/index.php/topic,23134.0.html I think it is helpful for us novice bowyers especially.
Logged

Offline Badger

  • Member
  • Posts: 8,124
Re: No set tiller
« Reply #12 on: October 29, 2014, 12:29:53 am »
  If you have paralell limbs the gizmo will give you not enough bend in the outer limbs and too much in the inner limbs. It will likley take more set.
Logged

Offline scp

  • Member
  • Posts: 660
Re: No set tiller
« Reply #13 on: October 29, 2014, 12:35:18 am »
Quote from: DC on October 28, 2014, 03:32:42 pm
When I'm trying no set tiller I'm supposed to pull to, say 16" and note the draw weight. Then pull an inch past that and then drop back to 16" and again note the draw weight. If it's less than the first time the bow is starting to take set. Then I'm supposed to stop and figure out what is causing the set.    What am I looking for? If it's 40# the first time and 38# the second time will there be a noticeable bend/hinge somewhere? What if the bend looks even, what else could it be? I'm a bit puzzled here.
Thanks
Don

You are describing Badger's no hysteresis tiller that might be impossible. If you are tillering, it is natural for the draw weight to go down at a fixed draw length, as the tillering progress. Otherwise how are you going to arrive at your target draw weight at your target draw length?
Logged

Offline jeffp51

  • Member
  • Posts: 1,641
Re: No set tiller
« Reply #14 on: October 29, 2014, 12:41:29 am »
Quote from: Badger on October 29, 2014, 12:29:53 am
  If you have paralell limbs the gizmo will give you not enough bend in the outer limbs and too much in the inner limbs. It will likley take more set.

Interesting. Is that because  you are shooting for a more elliptical bend?  Because the way I understand it, the gizmo indicates a constant curve, which would give you a perfect circle arc if you were to continue around.  I can see how the elliptical shape might cause less set.  What is the ideal curve for a bow?  Can that question even have an answer?
Logged
Pages: [1] 2
« previous next »