« previous next »
Pages: [1] 2

Author Topic: Finish?  (Read 3275 times)

0 Members and 1 Guest are viewing this topic.

Offline Blaflair2

  • Member
  • Posts: 2,042
Finish?
« on: September 15, 2013, 03:10:45 pm »
How many coats of oil should I put on. Thinking teal or tung oil. Then wanted to put a spray urethane on. Will that go over the oil?
Logged
Nothing ventured nothing gained

Offline bushboy

  • Member
  • Posts: 2,256
Re: Finish?
« Reply #1 on: September 15, 2013, 03:28:30 pm »
What type of wood is it?
Logged
Some like motorboats,I like kayaks,some like guns,I like bows,but not the wheelie type.

Offline Blaflair2

  • Member
  • Posts: 2,042
Re: Finish?
« Reply #2 on: September 15, 2013, 03:40:31 pm »
Osage
Logged
Nothing ventured nothing gained

Offline Blaflair2

  • Member
  • Posts: 2,042
Re: Finish?
« Reply #3 on: September 15, 2013, 03:42:50 pm »
Also I don't out anything on before I shoot it in?
Logged
Nothing ventured nothing gained

Offline wood_bandit99

  • Member
  • Posts: 234
  • Shoot straight my friends!!
Re: Finish?
« Reply #4 on: September 15, 2013, 03:49:03 pm »
Tung oil I would say at least 5 coats. But I constantly rub in oil. Every month I put on two coats to make them completely water proof.
Logged
Yew and osage, BEST. WOODS. EVER! Shoot straight my friends!!!

Offline Bryce

  • Global Moderator
  • Member
  • Posts: 3,125
  • Pacific Ghost Longbows
Re: Finish?
« Reply #5 on: September 15, 2013, 04:09:10 pm »
6-9
Logged
Clatskanie, Oregon

Offline Blaflair2

  • Member
  • Posts: 2,042
Re: Finish?
« Reply #6 on: September 15, 2013, 04:15:47 pm »
Will the urethane go over the tung oil ?
Logged
Nothing ventured nothing gained

Offline lostarrow

  • Member
  • Posts: 1,348
Re: Finish?
« Reply #7 on: September 15, 2013, 04:29:39 pm »
Test on scrap first. The poly won't  likely stick well in the long run over the oil. Three coats would be plenty for teak oil.  First soaks in , second hits the spots that soaked in more or got a thinner coat first time around, third evens everything out . Couple more if you're not convinced , but anymore and you are trying to build up a finish with a penetrating oil. Save the million coat finish for finishes that build up to give it depth, like poly or shelac. touch up as required.
« Last Edit: September 15, 2013, 04:36:11 pm by lostarrow »
Logged

Offline toomanyknots

  • Member
  • Posts: 3,132
Re: Finish?
« Reply #8 on: September 15, 2013, 04:55:29 pm »
I've added tru oil over tung oil. The tung oil was real tung oil, not the stuff from lowes. I waited 2 weeks, maybe a month, before doing the tru oil. The tung oil was just one coat though.
Logged
"The way of heaven is like the bending of a bow-
 the upper part is pressed down,
 the lower part is raised up,
 the part that has too much is reduced,
 the part that has too little is increased."

- Tao Te Ching, 77, A new translation by Victor H. Mair

Offline Gordon

  • Member
  • Posts: 3,299
Re: Finish?
« Reply #9 on: September 15, 2013, 08:26:04 pm »
You can spray urethane on over tung oil, but you better make sure that the tung oil has completely dried or the urethane finish will develop cracks.
Logged
Gordon

Offline Blaflair2

  • Member
  • Posts: 2,042
Re: Finish?
« Reply #10 on: September 15, 2013, 08:41:59 pm »
So I can just finish it with tung oil? And it'd be fine? Any advantages of tru oil
Logged
Nothing ventured nothing gained

Offline dbb

  • Member
  • Posts: 745
Re: Finish?
« Reply #11 on: September 19, 2013, 08:41:37 am »
Yes you can finish it with tungoil.
It will just take a lot longer to do it.
Logged
It's better to ask and look like a fool than not to ask and remain one...

Offline PEARL DRUMS

  • Member
  • Posts: 14,079
  • }}}--CK-->
Re: Finish?
« Reply #12 on: September 19, 2013, 09:13:32 am »
I use real Tung oil on most of my bows. I start with a base coat of shellac just to liven up the grain. Then I wipe on 4-6 coats of real Tung oil. Then after a week or so I wipe 2-4 coats of paste wax over it, however you can skip the wax if you want to. I like the cheap insurance of adding wax.
Logged
Only when the last tree has died and the last river has been poisoned and the last fish has been caught will we realize we cannot eat money.

Offline PEARL DRUMS

  • Member
  • Posts: 14,079
  • }}}--CK-->
Re: Finish?
« Reply #13 on: September 19, 2013, 09:16:42 am »
One more thing. If you choose a sunny, dry day to apply the tung oil, you can do at least 3 coats in a day by leaving it in the sunny, warm breeze. Ive done it many, many times. However, in a normal weather situation its one coat every 20-24 hours.
Logged
Only when the last tree has died and the last river has been poisoned and the last fish has been caught will we realize we cannot eat money.

Offline Pat B

  • Administrator
  • Member
  • Posts: 37,542
Re: Finish?
« Reply #14 on: September 19, 2013, 09:50:33 am »
Osage is pretty oily so why add more oil to the finish?   Just spray a few coats of poly and 0000steel wool rub down between coats.
Logged
Make the most of all that comes and the least of all that goes!    Pat Brennan  Brevard, NC
Pages: [1] 2
« previous next »