« previous next »
Pages: [1]

Author Topic: Bendy handle  (Read 1935 times)

0 Members and 1 Guest are viewing this topic.

Offline bow101

  • Member
  • Posts: 2,235
Bendy handle
« on: April 14, 2013, 11:18:05 pm »
Dun another ocean spray sapling,,,,,,,,,,but as stinking usual I took off to much material in the handle so its bending more than I like in the handle. What is the easiest & quickest way to beef it up.?
I was thinking to cut a small piece of maple and glue it on the back.
Logged
"The privilege of a lifetime is being who you are."  Joseph Campbell

Offline Pat B

  • Administrator
  • Member
  • Posts: 37,633
Re: Bendy handle
« Reply #1 on: April 14, 2013, 11:50:16 pm »
Once the handle area bends it is hard to add a handle. You could try adding a thin lam on the back and belly and they should flex enough to survive the bending. This should add a little stiffness to the handle area.
Logged
Make the most of all that comes and the least of all that goes!    Pat Brennan  Brevard, NC

Offline bow101

  • Member
  • Posts: 2,235
Re: Bendy handle
« Reply #2 on: April 15, 2013, 12:05:06 am »
Yup, a thin lam that's what I'll try............
Logged
"The privilege of a lifetime is being who you are."  Joseph Campbell

Offline Pat B

  • Administrator
  • Member
  • Posts: 37,633
Re: Bendy handle
« Reply #3 on: April 15, 2013, 12:30:27 am »
Feather them out well so they will bend evenly. I'd do that before glue up. It will make a cleaner application.  ;)
Logged
Make the most of all that comes and the least of all that goes!    Pat Brennan  Brevard, NC

Offline DarkSoul

  • Member
  • Posts: 1,315
    • Orion Bows
Re: Bendy handle
« Reply #4 on: April 15, 2013, 07:25:26 pm »
How on earth are you going to glue a thin lam to the curved, crowned and natural back of an ocean spray sapling? Sounds virtually impossible to me. By the time you got that back flat enough to accept a flat lam and glue, you've lost all integrity of that handle.

Heat treating the handle might make it slightly stiffer. Not by much, but it might be enough.
Logged
"Sonuit contento nervus ab arcu."
Ovid, Metamorphoses VI-286

Offline bow101

  • Member
  • Posts: 2,235
Re: Bendy handle
« Reply #5 on: April 15, 2013, 07:42:17 pm »
Flatten out the belly not the back,  add a piece.   ;D won;t lose all integrity of that handle if thick enough piece is used.
Logged
"The privilege of a lifetime is being who you are."  Joseph Campbell

Offline DarkSoul

  • Member
  • Posts: 1,315
    • Orion Bows
Re: Bendy handle
« Reply #6 on: April 15, 2013, 08:16:59 pm »
You initially said you'd glue it to the back of the bow ;)
Sure, gluing it to the belly is easier. Still, you need to be very careful to remove as little wood as possible. But even then, you run a risk of that added handle piece popping off.
Logged
"Sonuit contento nervus ab arcu."
Ovid, Metamorphoses VI-286

Offline bow101

  • Member
  • Posts: 2,235
Re: Bendy handle
« Reply #7 on: April 15, 2013, 08:24:08 pm »
Quote from: DarkSoul on April 15, 2013, 08:16:59 pm
You initially said you'd glue it to the back of the bow ;)
Sure, gluing it to the belly is easier. Still, you need to be very careful to remove as little wood as possible. But even then, you run a risk of that added handle piece popping off.

Lol.  just testing ya.. :)   I plan on having a heavy wrap of leather string and flat leather over top, it should hold.  The way it's turning out I'll be lucky to get 35-40# out of it. Its a skinny minny.
Logged
"The privilege of a lifetime is being who you are."  Joseph Campbell

Offline PEARL DRUMS

  • Member
  • Posts: 14,079
  • }}}--CK-->
Re: Bendy handle
« Reply #8 on: April 15, 2013, 08:27:39 pm »
Why not take some wet rawhide lace and wrap itt very tightly, while stretching it out, around the center out say 3-4". Give it a good bath of TBIII immediatley after wrapping. Then let it all cure for at least 4-5 days. Seems to me that would add a few pounds of resistance back in the handle as it constricts? Call me crazy.
Logged
Only when the last tree has died and the last river has been poisoned and the last fish has been caught will we realize we cannot eat money.

Offline adb

  • Member
  • Posts: 5,339
Re: Bendy handle
« Reply #9 on: April 15, 2013, 08:32:51 pm »
Nope... don't see that working. I've been down this road before, and I tried all your ideas. Everything I tried just popped off. I don't see rawhide adding any structural integrity to a bending handle. You could build up the grip with rawhide, but that's about it. Chalk it up as part of the learning curve. Even out your tiller and just live with the end result.
« Last Edit: April 16, 2013, 11:09:51 am by adb »
Logged

Offline bow101

  • Member
  • Posts: 2,235
Re: Bendy handle
« Reply #10 on: April 15, 2013, 11:35:40 pm »
At any rate I will try to save it. ???  It's my 3rd. attempt at an Ocean Spray. Maybe try a cable backed system, something to take the strain off the handle area, still have more room for scraping the mid limb sections.  ::)
Logged
"The privilege of a lifetime is being who you are."  Joseph Campbell

Offline gpw

  • Member
  • Posts: 149
Re: Bendy handle
« Reply #11 on: April 16, 2013, 09:24:56 am »
  We sometimes resorted to a more primitive method and just tied/wrapped  on the “handle” with Jute string , that way everything bent a little , and nothing popped off ... It looked a little “crude” , bit it was “primitive” ... and it worked ...
Logged
Pages: [1]
« previous next »