« previous next »
Pages: [1]

Author Topic: nock/spline jig  (Read 4346 times)

0 Members and 2 Guests are viewing this topic.

Offline bubby

  • Member
  • Posts: 11,054
nock/spline jig
« on: January 23, 2012, 09:15:59 pm »
we built this jig for cutting in nocks and nock splines, work's pretty good, Bub
Logged
failure is an option, everyone fails, it's how you handle it that matters.
The few the proud the 27🏹

Offline Elktracker

  • Member
  • Posts: 1,964
  • Josh
Re: nock/spline jig
« Reply #1 on: January 24, 2012, 04:15:33 pm »
How does it work Bubby I dont get it :-[

Josh
Logged
my friends think my shops a mess, my wife thinks I have too much bow wood, my neighbors think im redneck white trash and they may all be right on the money!!

Josh Vance  Netarts OR. (Tillamook)

Offline bubby

  • Member
  • Posts: 11,054
Re: nock/spline jig
« Reply #2 on: January 24, 2012, 04:18:09 pm »
you stick the arrow in the hole and run it through a tablesaw Josh, Bub
Logged
failure is an option, everyone fails, it's how you handle it that matters.
The few the proud the 27🏹

Offline Elktracker

  • Member
  • Posts: 1,964
  • Josh
Re: nock/spline jig
« Reply #3 on: January 24, 2012, 04:40:45 pm »
O ok I see now :D Thanks thats pretty cool I need to try one of these thanks for sharing

Josh
Logged
my friends think my shops a mess, my wife thinks I have too much bow wood, my neighbors think im redneck white trash and they may all be right on the money!!

Josh Vance  Netarts OR. (Tillamook)

Offline bubby

  • Member
  • Posts: 11,054
Re: nock/spline jig
« Reply #4 on: January 24, 2012, 04:59:07 pm »
josh i allways have troble cutting in my nocks, this makes them the same every time, i cut the reinforcing spline a little deeper than the nock, it look's a little nicer, Bub
Logged
failure is an option, everyone fails, it's how you handle it that matters.
The few the proud the 27🏹

Offline Elktracker

  • Member
  • Posts: 1,964
  • Josh
Re: nock/spline jig
« Reply #5 on: January 24, 2012, 05:05:29 pm »
I have only done a few self knocks but the ones I did were a bit tough to get a good cut on the knock. I can see where this would really help! Thanks again

Josh
Logged
my friends think my shops a mess, my wife thinks I have too much bow wood, my neighbors think im redneck white trash and they may all be right on the money!!

Josh Vance  Netarts OR. (Tillamook)

Offline Bernal

  • Member
  • Posts: 31
Re: nock/spline jig
« Reply #6 on: February 02, 2012, 05:05:02 pm »
Bub, thanks for sharing that photo. I just made a jig like this and it worked perfectly for slotting the horn insert and then the nock cut. I couldn't be happier and it only took about 15 minutes to make it out of a nice piece of hardwood that I had sitting around.
Logged

Offline Rcdeer

  • Member
  • Posts: 108
  • Old School..selfbows an flintlocks
Re: nock/spline jig
« Reply #7 on: April 30, 2012, 10:28:51 am »
thanks!!! been lookin for how I could cut self nocks..gotta try it!!
Logged
A Promise Made is a Debt Unpaid
..Upstate N.Y.
Pages: [1]
« previous next »