Author Topic: First bow build help, done??  (Read 4362 times)

0 Members and 1 Guest are viewing this topic.

Offline Del the cat

  • Member
  • Posts: 8,322
    • Derek Hutchison Native Wood Self Bows
Re: First bow build help, please
« Reply #15 on: July 30, 2011, 05:33:51 pm »
Ah, yes but all this not level stuff is countered by the "lower limb stronger argument" :o
... sooooo, if the left limb is the lower limb.
And remember if your back is to the wind in the Northern hemisphere then low pressure is on your left ::).
I reckon that baby is close enough for jazz :laugh:
Del
Health warning, these posts may contain traces of nut.

Offline frankg

  • Member
  • Posts: 107
Re: First bow build help, please
« Reply #16 on: July 30, 2011, 06:17:14 pm »
Spent the morning scraping and checking (after adjusting graph to square). Got hot on porch and am now at 55# at 23" draw :)

Heres 20" on the stick . I think I got the left limb adjusted and a tad weaker now than right one . Now if they will stay that way till I get to target draw / wt .



South of Klamath Falls OR , North of Calif border .

Offline snag

  • Member
  • Posts: 419
Re: First bow build help, please
« Reply #17 on: July 30, 2011, 08:41:18 pm »
I thought the lower limb was to be slightly stiffer than the upper limb? Wasn't the left limb going to be the lower limb?
Is. 49:2 ....He made me a polished arrow and concealed me in His quiver.

Offline frankg

  • Member
  • Posts: 107
Re: First bow build help, please
« Reply #18 on: July 30, 2011, 09:49:04 pm »
The left was to be upper because of the way the limbs naturally bend to the right. I thought if they were positioned to bend left they might beat my arm up when shooting. The left (top now)was a lot stiffer than the right (bottem finally) untill I gave it more strokes than the other gradually taking it down . Hope it works out as I want .
South of Klamath Falls OR , North of Calif border .

Offline frankg

  • Member
  • Posts: 107
Re: First bow build help, please
« Reply #19 on: July 31, 2011, 01:31:44 am »
Starting to get nervous and a bit excited all at the same time now  ;D ;D Im at 24" and 50# !! Its still looking like it does in last pic as far as tiller .  I made a string from two strands of  hemp , waxed up real good in anticipation . Hopefully have success tomorrow  ;D ;D

A  question............ should I start thinning the last 6" or so of the tip ends ? they are still a bit thicker back to belly ?

Thanks for the input !!
South of Klamath Falls OR , North of Calif border .

Offline frankg

  • Member
  • Posts: 107
Re: First bow build help, Done ???
« Reply #20 on: July 31, 2011, 06:54:17 pm »
After lots and lots of scrapin I think Im did :) I have 50# at 27" and callin it close nuf ! I got some stain dryin on it an gettin ready for couple coats of tung oil before I put a buckskin wrap on handle. Heres a pic of 26" on stick.

 
South of Klamath Falls OR , North of Calif border .

Offline dbb

  • Member
  • Posts: 745
Re: First bow build help, please
« Reply #21 on: July 31, 2011, 07:49:46 pm »
If my frst looked like that id be damn proud ;)

/Mikael
P.s The tillerstick is off the gridpaper by a half inch or so,a bit weird to make sense of it at first. D.s
It's better to ask and look like a fool than not to ask and remain one...

Offline frankg

  • Member
  • Posts: 107
Re: First bow build help, done??
« Reply #22 on: July 31, 2011, 09:32:46 pm »
Thanks dbb ! Im tickled it came out without blowing up ! Got a lot of good guidence here ! That graph thing slipped on my nail (wind blowing some). The tung oil is drying its second coat now .
South of Klamath Falls OR , North of Calif border .

Offline Del the cat

  • Member
  • Posts: 8,322
    • Derek Hutchison Native Wood Self Bows
Re: First bow build help, done??
« Reply #23 on: August 01, 2011, 06:08:23 am »
I'm working on my first Osage bow. If it turns out as well as that I'll be a happy cat :laugh:.
Del
Health warning, these posts may contain traces of nut.

Offline frankg

  • Member
  • Posts: 107
Re: First bow build help, done??
« Reply #24 on: August 01, 2011, 06:59:28 pm »
Thanks Del ! I have the grip on now an will post a pic after bit of how it turned out.
South of Klamath Falls OR , North of Calif border .