« previous next »
Pages: [1] 2

Author Topic: First attempt  (Read 4076 times)

0 Members and 1 Guest are viewing this topic.

Offline jham

  • Member
  • Posts: 41
First attempt
« on: May 31, 2011, 04:31:25 pm »
Just got back with a red oak board, wanting some recommendations for layout. Im planning on 68" ntn, 40-45lbs @ my draw of 29 inches. I have been reading on this site for a long time now, and know you guys are awesome at making bows. I have some maple pieces Im going to try to glue onto the handle area and use for nock overlays. Im hoping that this can turn out to be a nice bow, if not I will keep trying. Any recommendations on width at the fades? Thinking a pryamid style with a small arrow shelf built in. Thanks for any help
Logged

Offline doulosparachristos

  • Member
  • Posts: 145
Re: First attempt
« Reply #1 on: May 31, 2011, 04:43:25 pm »
hello, im up to the same thing right now as well, i found this VERY helpful ;) enjoy    http://tradgang.com/cgi-bin/ultimatebb.cgi?ubb=get_topic;f=125;t=002064;p=1
Logged
Philippians 3: 7-11

Offline jham

  • Member
  • Posts: 41
Re: First attempt
« Reply #2 on: May 31, 2011, 05:09:05 pm »
I read that one last night, thanks  ;D I know that one was overbuilt, and was a heavier bow. I was wondering if I could go down to 2", but my tablesaw just threw the belt and pulley off trying to cut some of the maple.  ??? So until I can get Dad to help fix it I guess I will leave it 2.5".
Logged

Offline Ifrit617

  • Member
  • Posts: 1,596
Re: First attempt
« Reply #3 on: May 31, 2011, 06:15:08 pm »
Id go with 2" fades straight tapering to 3/8 inch nocks. 8" non bending  handle section...( 4 inch handle and 2 inch fades)... 66" long since it is your first attempt.  If you tiller carefully and slow this design will make a very fast hard-hitting bow... Good luck:)
Logged

Offline PEARL DRUMS

  • Member
  • Posts: 14,079
  • }}}--CK-->
Re: First attempt
« Reply #4 on: May 31, 2011, 07:47:18 pm »
Quote from: Ifrit617 on May 31, 2011, 06:15:08 pm
Id go with 2" fades straight tapering to 3/8 inch nocks. 8" non bending  handle section...( 4 inch handle and 2 inch fades)... 66" long since it is your first attempt.  If you tiller carefully and slow this design will make a very fast hard-hitting bow... Good luck:)

That goes double for me......................except I would add 6" of length to it for your draw. I have built long and short oak board bows and they all stayed together fine, but the longer ones took on very little set and kept their initial "zing" a little more so than the shorter bows. Just my .0124735412 cents.
Logged
Only when the last tree has died and the last river has been poisoned and the last fish has been caught will we realize we cannot eat money.

Offline bubby

  • Member
  • Posts: 11,054
Re: First attempt
« Reply #5 on: May 31, 2011, 08:09:53 pm »
this red oak bow is 2" at the fades down to 3/8" tips 66" @27" it's 40#, I riped the belly thickness on the tablesaw to the start of the fades and finished up on the bandsaw, I cut the limb @ 9/16" thick, but you can go a touch thicker to be safe,this board was quartersawn but with a good board you will be fine, hope this helps, Bub
Logged
failure is an option, everyone fails, it's how you handle it that matters.
The few the proud the 27🏹

Offline jham

  • Member
  • Posts: 41
Re: First attempt
« Reply #6 on: May 31, 2011, 11:40:39 pm »
so far I have the rough outline cut out, went with 68" ntn,2.5" at the fades and 1/2" at the tips, may take the tips down some later. My plan to use maple on the handle didnt work out, killed the table saw trying to cut a block out of a small piece of firewood lol. I already see a few things I'm not happy with, will do it a little differently on the next bow. Putting a bandsaw on my wishlist, still not sure how I'm going to thin down the limbs. May end up taking a d/a sander to them.
Logged

Offline Pappy

  • Global Moderator
  • Member
  • Posts: 31,915
  • if you have to ask you wouldn't understand ,Tenn.
Re: First attempt
« Reply #7 on: June 01, 2011, 09:24:23 am »
You can thin them with a rasp/draw knife and scraper,A band saw is great and I use one all the time but I have built many years back without one. Just a little slower and it's not a race. :) Don't let not having a band saw hold you back. :)
   Pappy
Logged
Clarksville,Tennessee
TwinOaks Bowhunters
Life is Good

Offline crooketarrow

  • Member
  • Posts: 2,790
Re: First attempt
« Reply #8 on: June 01, 2011, 09:36:25 am »
   Your first bow they aways has a special place in your heart. GOOD LUCK
Logged
DEAD IS DEAD NO MATTER HOW FAST YOUR ARROW GETS THERE
20 YEARS OF DOING 20 YEARS OF LEARNING 20 YEARS OF TEACHING

Offline degoins

  • Member
  • Posts: 20
Re: First attempt
« Reply #9 on: June 01, 2011, 12:26:49 pm »
Hey guys,
the only good boards (red oak) I've been able to find so far are only and 1 3/4" wide. How would you do the thickness and lay out on that? i'm hoping for around 50# - 60# at 25" .

Thanks
Logged

Offline degoins

  • Member
  • Posts: 20
Re: First attempt
« Reply #10 on: June 01, 2011, 02:16:36 pm »
Thanks ScottD,
it may be 1 1/2" now that i think about it.....and i did get it from Lowes. I'd like to make it without gluing on a riser too.....just like the looks of it better that way.
Logged

Offline bubby

  • Member
  • Posts: 11,054
Re: First attempt
« Reply #11 on: June 01, 2011, 03:45:01 pm »
hardwood suppliers are a better bet for good boards, and in my experiance they are generaly less spendy for higher quality wood, plus their are way more options, Bub
Logged
failure is an option, everyone fails, it's how you handle it that matters.
The few the proud the 27🏹

Offline degoins

  • Member
  • Posts: 20
Re: First attempt
« Reply #12 on: June 01, 2011, 04:48:54 pm »
Hey Bub,
there's a place here that I think I could get some good wood from, but Lowes is on my way home from work and I decided to stop by there and see what they had. If this turns out good, I'll go to the other place and see what they have.
Logged

Offline jham

  • Member
  • Posts: 41
Re: First attempt
« Reply #13 on: June 02, 2011, 01:03:27 am »
well day 2 I finished shaping around the handle and started thinning the limbs. Its starting to look like a bow even if its not bending yet
Logged

Offline bubby

  • Member
  • Posts: 11,054
Re: First attempt
« Reply #14 on: June 02, 2011, 07:34:43 am »
jham, you can cut the bow out with a skillsaw if you are proficent with one, or find a buddy with a table saw or bandsaw, or ya can reduce it with a hatchet, surform or anything that will remove wood, Bub
Logged
failure is an option, everyone fails, it's how you handle it that matters.
The few the proud the 27🏹
Pages: [1] 2
« previous next »