Author Topic: Short Ipe Paddle Bow?  (Read 3756 times)

0 Members and 1 Guest are viewing this topic.

Offline Tim B

  • Member
  • Posts: 96
Short Ipe Paddle Bow?
« on: February 16, 2011, 03:01:37 pm »
Has anyone made a short paddle bow say around 55" out of Ipe? I am going to make one that is boo backed 2" at widest part of limb and try for as close to 26" draw as possible and hope for around 40lbs of draw weight. Any thoughts or suggestions?

Offline JackCrafty

  • Global Moderator
  • Member
  • Posts: 5,628
  • Sorry Officer, I was just gathering "materials".
Re: Short Ipe Paddle Bow?
« Reply #1 on: February 16, 2011, 03:12:49 pm »
Yep, I made one about 47" long, unbacked, from an ipe board.  Draw length was about 23" but I think the tips were too heavy -- the hand shock was in issue.

I would make the tips as thin as possible.  Also, you could induce a little recurve in the tips during glue up.   ;D
Any critter tastes good with enough butter on it.

Patrick Blank
Midland, Texas
Youtube: JackCrafty, Allergic Hobbit, Patrick Blank

Where's Rock? Public Waterways, Road Cuts, Landscape Supply, Knap-Ins.
How to Cook It?  200° for 24hrs then 275° to 500° for 4hrs (depending on type), Cool for 12hr

Offline Tim B

  • Member
  • Posts: 96
Re: Short Ipe Paddle Bow?
« Reply #2 on: February 16, 2011, 03:19:27 pm »
Scott how long was your bow? The design you have looks really close to the boo backed Brazilian redwood bow I made that was 58" and 1 1/4" wide that shoots really nice. The piece of ipe I have for this bow was left over from a 10' board I had bought and cut into longer bellies for bows and didn't want to waste it. If all else fails I will make it for a kid but would like to see if I can get a short hunter from this one.

Offline Tim B

  • Member
  • Posts: 96
Re: Short Ipe Paddle Bow?
« Reply #3 on: February 16, 2011, 04:03:08 pm »
I guess I'll try to go between 1 1/4" and 1 1/2" then with the 55" length and see what happens. Being 5" shorter it will have to bend through the handle to get anywhere close to 26" of draw length. Nothing ventured nothing lost eh?

Offline bubby

  • Member
  • Posts: 11,054
Re: Short Ipe Paddle Bow?
« Reply #4 on: February 16, 2011, 04:59:16 pm »
I made a gull wing white oak backed epe, 50" got 29" of draw @ 46# and a really smooth shooter, Bub
failure is an option, everyone fails, it's how you handle it that matters.
The few the proud the 27🏹

Offline Tim B

  • Member
  • Posts: 96
Re: Short Ipe Paddle Bow?
« Reply #5 on: February 16, 2011, 05:55:08 pm »
Man that is impressive to get that much draw length from that bow Bubby, did the gull wing design reduce the amount of set that the bow would take?

Offline Tim B

  • Member
  • Posts: 96
Re: Short Ipe Paddle Bow?
« Reply #6 on: February 16, 2011, 06:00:49 pm »
Scott was your handle built up on that bow?

Offline bubby

  • Member
  • Posts: 11,054
Re: Short Ipe Paddle Bow?
« Reply #7 on: February 16, 2011, 06:54:08 pm »
no noticeable set as the epe just springs back, plus the fact that there's less string tension they can stay strung for a long time with no apparent side effects, not sure you'd get the same results with a self bow thou, Bub
failure is an option, everyone fails, it's how you handle it that matters.
The few the proud the 27🏹

Offline fusizoli

  • Member
  • Posts: 238
Re: Short Ipe Paddle Bow?
« Reply #8 on: February 16, 2011, 07:06:18 pm »
Scott, thats a very nice bow. I think I ve missed the original post. Great work! Nice dogy!