Author Topic: router jig question  (Read 3022 times)

0 Members and 1 Guest are viewing this topic.

Offline k-hat

  • Member
  • Posts: 1,058
router jig question
« on: October 22, 2012, 12:45:23 pm »
I've been perusing all the arrow shafting router jigs and still have a couple of questions:

For 11/32 shafts:

what is the best bit?
are you routing them to 3/8 and then finish sanding down to 11/32, or are you just using 3/8" shafts?  (the smallest guide block i saw was 3/8)

i have a 21000 rpm router and table, and am planning to make the infeed and guide blocks from 1/2" aluminum that i have on hand.

thanks!

Offline Buckeye Guy

  • Member
  • Posts: 3,033
Re: router jig question
« Reply #1 on: October 22, 2012, 01:22:42 pm »
Typically 3/8 then compress to 11/32 you will want steel block for that part !
Guy
Guy Dasher
The Marshall Primitive Archery Rendezvous
Primitive Archery Society
Having  fun
To God be the glory !

Offline k-hat

  • Member
  • Posts: 1,058
Re: router jig question
« Reply #2 on: October 22, 2012, 01:40:41 pm »
ok, so if i buy a 11/32 bit and drill the hole in an aluminum block, i run the shaft through this with the drill after using the router jig?  Will the compression affect stainability, etc?  If so, i suppose i could jig it, stain it, then compress it?

Offline carpentertimw

  • Member
  • Posts: 42
Re: router jig question
« Reply #3 on: October 22, 2012, 04:41:34 pm »
i think aluminum would wear away too fast, you want steel. i dont know if 1/8" would work but thats easy to drill also.

Offline k-hat

  • Member
  • Posts: 1,058
Re: router jig question
« Reply #4 on: October 22, 2012, 05:18:06 pm »
Sorry, missed the steel part on buckeye's post, not tryna be that hardheaded ;)

I'll have to see if i have some, though i'm sure i can get some from depot.

thanks for the help guys, lookn forward to gettin this going. 

Offline Buckeye Guy

  • Member
  • Posts: 3,033
Re: router jig question
« Reply #5 on: October 23, 2012, 08:48:50 pm »
It will stain differently (lighter in color) but will still stain !
Test a piece first then sand it a little with fine sandpaper and try again !
Guy Dasher
The Marshall Primitive Archery Rendezvous
Primitive Archery Society
Having  fun
To God be the glory !

Offline k-hat

  • Member
  • Posts: 1,058
Re: router jig question
« Reply #6 on: October 24, 2012, 09:31:21 am »
Ok, thanks guy.  I hope to get it set up this weekend.  I'll let ya know how it goes when i get it going!

Offline soy

  • Member
  • Posts: 2,897
  • pm106221
Re: router jig question
« Reply #7 on: October 26, 2012, 05:56:16 am »
Well brass work in place of steel????
Is this bow making a sickness? or the cure...

Offline carpentertimw

  • Member
  • Posts: 42
Re: router jig question
« Reply #8 on: October 26, 2012, 05:48:15 pm »
i think brass would be too soft also, a piece of steel is only a few dollars and not that hard to drill, but if you use 1/8" it leaves spiral markings. i'm going to get a thicker piece to try and that should cure that. :)

mdWill85

  • Guest
Re: router jig question
« Reply #9 on: October 27, 2012, 01:04:33 am »
I use a thinner steel plate. You can keep from having the spiral problem if you feed your shaft in slower.

Offline nclonghunter

  • Member
  • Posts: 1,779
Re: router jig question
« Reply #10 on: October 27, 2012, 01:06:41 pm »
Any pictures of this process?
There are no bad knappers, only bad flakes