« previous next »
Pages: [1]

Author Topic: Bendy handle question.  (Read 1743 times)

0 Members and 1 Guest are viewing this topic.

Offline Calamitus

  • Member
  • Posts: 59
Bendy handle question.
« on: January 23, 2013, 02:45:02 am »
I want to build a bow, 50#, out of red oak board. I want it shorter than 60" and was wondering if a bendy handle can be narrower (1.25"?) and still be safe. I can build up the shape with rawhide ( best glue for that?). Thanks.
Logged

Offline Cardboard_Duck

  • Member
  • Posts: 282
  • Winter Haven, FL
Re: Bendy handle question.
« Reply #1 on: January 23, 2013, 09:51:51 am »
I have never built one from red oak, but I have two that are an inch wide at the widest point.

One is osage that is 58" TtT and about #50lbs @ 28" and the other is a bamboo backed ipe that is 64" TtT and is about #55 @ 28". They both shoot great and are my favorite to shoot.







Logged
>>>---------->

Offline lesken2011

  • Member
  • Posts: 2,063
  • Kenny
Re: Bendy handle question.
« Reply #2 on: January 23, 2013, 09:53:18 am »
I made a white oak bendy handle that was 60" ttt and 58" n2n. It was 1.5" wide, though, and linen backed for safety even though the grain was perfectly straight. It easily could have been 50#, but I was making it for a youth and took it down to about 40# at 28"....35# at his draw length. Here is a pic.


I am less confident with red oak as most that I have seen doesn't seem as dense to me.
« Last Edit: January 01, 2019, 10:04:19 am by lesken2011 »
Logged
For by grace you have been saved through faith, and that not of yourselves; it is the gift of God, not of works, lest anyone should boast.

Ephesians 2:8-9

Kenny from Mississippi, USA

Offline Dictionary

  • Member
  • Posts: 717
Re: Bendy handle question.
« Reply #3 on: January 23, 2013, 10:41:47 am »
1 1/4 will be fine. Id shoot for more in the 40-45 pound range though to be safe. I'd make it longer than 60 inches if it is for a 50 pound bow. Then again i build safe bows. Go for it.
Logged
"I started developing an eye for those smooth curves as a young man.  Now that my hair is greying and my middle spreading I make bows instead."

-JW_Halverson

Offline autologus

  • Member
  • Posts: 1,092
Re: Bendy handle question.
« Reply #4 on: January 23, 2013, 11:25:34 am »
I'm building one right now out of red oak that is 1.25" wide at the handle and have it ready for the tree.   I am hoping it will come in at 45 - 50# we will see.  Mine is 59" ntn.

Grady
Logged
Proud Hillbilly from Arkansas.

Offline bubby

  • Member
  • Posts: 11,054
Re: Bendy handle question.
« Reply #5 on: January 23, 2013, 03:05:55 pm »
tb will work to glue the rawhide, with red oak under 60" I would back it with rawhide for safety if it was me
Logged
failure is an option, everyone fails, it's how you handle it that matters.
The few the proud the 27🏹

Offline crooketarrow

  • Member
  • Posts: 2,790
Re: Bendy handle question.
« Reply #6 on: January 23, 2013, 03:19:26 pm »
   I never built a any bendy handle oak but have elm, hackberry, quite a few hickory and osage any where from 52 to 58 inch range, 50 to 60 pounds. These were anywhere form a inch to 1 1/4"s with no problems..
Logged
DEAD IS DEAD NO MATTER HOW FAST YOUR ARROW GETS THERE
20 YEARS OF DOING 20 YEARS OF LEARNING 20 YEARS OF TEACHING
Pages: [1]
« previous next »