Primitive Archer

Main Discussion Area => Bows => Topic started by: Justin Steele on April 28, 2012, 12:17:21 am

Title: new to bow making- first stave
Post by: Justin Steele on April 28, 2012, 12:17:21 am

This is my first attempt at building a bow. I went out and cut a hickory tree then roughed it in with a hatchet. There are a few knots in it-which I'm sure will give me trouble but this is my first bow and I want to use what I have. Any feedback would be greatly appreciated. 

Title: Re: new to bow making- first stave
Post by: SA on April 28, 2012, 12:33:50 am

the knots on the side are what might give ya trouble  , be carefull not to cut into them, try to leave some wood around them . if there towards the tips you might be able to just cut'em out when you taper down 8'' or 10'' or so ::) . other than that looks like a good little stick,have fun and enjoy the process. :)

oh and you might want to strap it down to a 2x4 or something while it drys so you don't have a twisted warped stave in a few months .

Title: Re: new to bow making- first stave
Post by: Justin Steele on April 28, 2012, 12:53:56 am

Thanks for the tip on strapping it down. I'm wanting to build a simple d bow and am hoping that the taper of my bow will wind up inside of the knot (the one on the side) as opposed to through it but I'm not really sure. If it ends up being directly in the way what would I do? Make a wider bow? Use it for firewood? Thanks for the advice.

Title: Re: new to bow making- first stave
Post by: Bevan R. on April 28, 2012, 12:56:29 am

It looks to me like you have quite a bunch of wood to work with. I would strap it down, slide it under the bed, look for more wood, start on arrows.

Title: Re: new to bow making- first stave
Post by: toomanyknots on April 28, 2012, 02:14:59 am

And so it begins...

Title: Re: new to bow making- first stave
Post by: Dictionary on April 28, 2012, 10:36:56 am

i'd rough it out a little more till its bending slightly when floor tillered. It'll dry faster. I can't really tell how much wood you have on that stave though.

Title: Re: new to bow making- first stave
Post by: RDK on April 28, 2012, 10:54:09 am

just to add......take your time with the side knots like sa said...especially if you decide to rough it out a bit more......  there are some excellent pics that have been posted showing how to deal with--knotty problems......

enjoy!!!

Title: Re: new to bow making- first stave
Post by: PEARL DRUMS on April 28, 2012, 07:36:26 pm

If you have access to more wood I would go find something much cleaner to try your first bow with. Hickory of any sort is tough, almost unbreakable stuff. Find some with few or no knots to ensure your chances of an acutal shooting bow.

Title: Re: new to bow making- first stave
Post by: mullet on April 28, 2012, 09:24:32 pm

I'd rough it out a little more and put it away to dry after sealing it.

Title: Re: new to bow making- first stave
Post by: Justin Steele on April 29, 2012, 03:47:48 pm

Thanks for the advice. I think I'm gonna rough it in some more, seal it, and strap it down. I'm also gonna collect some more staves though. I have 100 acres of woods to work with. I also have about 20 straight black locust posts hanging in the barn that were used to hang tobacco from 20 years ago so they are well seasoned.

Title: Re: new to bow making- first stave
Post by: Justin Steele on April 29, 2012, 03:49:27 pm

 I'm also gonna collect some sinew and turkey feathers and try to find some good wood for arrows. Anyone suggestions on wood in west Virginia?