Primitive Archer
Main Discussion Area => Arrows => Topic started by: archerforlife2 on July 03, 2011, 02:58:37 pm
-
how does everybody on here cut their cane shafts i think a chop saw couldn't work would it so hat do i cut them, with? kinda a stupid question but i don't know ;D
-
i used a small pair of hand pruners-worked great. also took the 3/8" open end wrench for reference.
-
okay sweet thanks :D
-
I use a hand held coping(sp?) saw to cut all my arrow woods. It's got a 7" long thin blade and a 6" throat. Cuts real smooth, easy to pack and handle. I use 1, 2 and 3 hack saw blades to cut nocks and slots for points. When using multiple blades I tape them together at the ends w/ masking tape. It doesn't get as sticky as duct tape.
-
when cutting them in the woods i just use a pocket knife, leave extra and make a slash cut. cutting to length the easiest thing i have found was a tubing cutter, works great.
-
im going to use a high speed tubing cutter i forgot i had it >:D it was buried underneath a bunch of stuff in my garage
-
the one i use is not a power cutter, just a simple hand cutter, you just screw it in till you have some contact, then spin then tighten more and spin again. not sure how a high speed cutter will work, definately let us know.
-
I use hand pruners for cane and hardwood shoots. I prefer bypass pruners instead of an anvil type pruner. The anvil type tends to crush the cane and shoots. Whatever you use be sure it is sharp.
-
I use a long knife in the woods and then the band saw or jig saw to fine tune it.
-
I use a jab saw (plumbers hacksaw) in the woods and a dremel tool with a metal cut off blade in the shop.
-
hand pruners and band saw when dry.
-
i also carry one of those bags your folding chair comes in my backpack whenever i hit the woods. you know the ones with the shoulder strap. makes a great way to carry shoot shafts. pretty sure most here see shoots shafts and bow staves in trees and shrubs when we're in the woods.....
-
depending on when you are cutting them. hand pruners cutting them fresh. i use a small hand saw when cutting them after dried. i pull the saw backwards across the cane, so that the teeth do not snag the fibers.
-
i use a pair of gerber hand pruners used to use a sharp knife but stuck a angled cut piece of cane through my new waders(from an angled cut piece i probaly cut myself the cane is like a the old vietnamese pungee stick so becareful and remember that the others use the woods as well. but that is what i use in the woods and the 3/8 open end wrench is a great idea.
john
-
The best way I know to cut across a bamboo shaft cleanly is with a sharp knife. This would be after the shaft is dry and straight.
Lay the shaft on a cutting board of some kind. Using a sharp knife and firm pressure run the knife across the shaft so that the shaft rolls underneath. Do this back and forth applying greater pressure and the balde will cut in a clean line round the shaft and cut straight through. The ciut is so clean it is ploished and absolutely without tear. straight and at right angles. It's very simple but very very effective.
I use a frost mora bushcraft knife but any good thin sharp knife blade should work.
-
When in the field I use hand pruners but they can tend to crush the culm (cane shaft) a bit causing some splitting. So when I get home i use a coping saw or back saw to trim up the ends.
If you cut straight down on the shaft, like you would a piece of wood, what will happen near the end of your cut is the part you are cutting off will push down all of a sudden and pull a strip of cane down the part of shaft you intend to keep. To avoid this I start a shallow cut or kerf on one side and stop. Then I rotate to the other side and begin cutting on that side until I meet the kerf mark I just made. This keeps the cane in good shape with no peeling. When you meet your kerf the part that breaks off does not push down with the radial grain. Instead it pushes laterally to the radial grain preventing the peel.
If that does not make sense just try it both ways and you will see the difference. ;)
-
I'm new to the bamboo scene but am " hooked ". I've been doing all my cutting with a very sharp knife, using the roll and press method to cut for tapering, and using a knife in conjunction with a mitre box when installing inserts or foreshafts and need an exact 90 degree cut. I haven't harvested any of my own yet.
-
FAW...I can tell you from first hand experiance. Cutting cane in the field, it's a bad idea to use a knife and cut down at an angle. I got 8 stitcheson the top of my hand between my index finger and thumb :-[ >:(
-
Hillbilly, sorry to hear about your hand, ouch!! As I said I have never harvested cane or bamboo yet and your lesson will be well heeded if I am ever able to do my own.