Primitive Archer
Main Discussion Area => English Warbow => Topic started by: Dag on April 21, 2011, 09:28:04 pm
-
Hi everyone,
I've been sit on this stave for awhile and started scraping away a little today. Please give me some tips on where to go from here.
Upper limb is on the right.
-
looks nice, i think on both sides it needs a little more bending near the tips, what are the dimensions, weight and materials, it looks good so far though, cant wait to see the progress ;D
good luck
noel
-
Thanks Fish. I was so excited to post earlier I forgot to give you all the specs on the stave. It is 76" long and 1 3/16" wide at the handle. Hickory belly/Ipe/Bamboo backing. Ideally, I would like to hit #130 at 32" but I'd be happy for anything over #90.
-
looks like a nice combo, it also looks like we have similar interests when it comes to bows ;D, im actually planing a hickory backed ipe longbow around 80 long and 130-150lbs at 32. that will start after the ash one im building, are you going to do self nocks or horn
noel
-
Nice! Yes I like this lamination combo quite a lot. It makes for a very fast bow. I'll probably do self nocks on this one. That Hickory/Ipe sounds awesome! Should loose arrows like lasers! :D
-
one can only hope, if you can though, i would at least try to put overlays on, iv'e had an osage bow around 100 start to split itself because the tips wasn't reinforced, and partially the design(oops ::)), i just would hate to see such a beautiful bow ruined
good luck
noel
-
Dag,
Interesting tri-lam combo. Personally, I think hickory is the worst belly wood there is. If it was me, I'd have used the ipe as my belly wood, and bamboo or hicory as core/backing woods. That being said, i hope it works out for you anyway.
Also, you need a tiller tree, and you also need to get rid of that overly long tiller string. My longest 'long string' is usually no more than the same length as the bow. It does, however, look like your tips are very stiff, and if you're not careful, a hinge is being born in your right limb.
-
Thats funny I have just done the exact same thing with a hickory Ipe Hickory bow made to 130lb at 32", as abd said hickory isnt the best so try your best to get a perfect tiller, I use it as a weight trainer.
It can be difficult to gauge tiller on a long string but it is bending more just after the handle and not enough mid limb or at the tips, if I wsa you make the mid limb bend more then when you work the bow to 24" draw with a braced profile see what the tips are doing then.
-
Thats funny I have just done the exact same thing with a hickory Ipe Hickory bow made to 130lb at 32", as abd said hickory isnt the best so try your best to get a perfect tiller, I use it as a weight trainer.
It can be difficult to gauge tiller on a long string but it is bending more just after the handle and not enough mid limb or at the tips, if I wsa you make the mid limb bend more then when you work the bow to 24" draw with a braced profile see what the tips are doing then.
Could you post a picture of this bow? Even better, a picture of you shooting this bow?
-
(http://i270.photobucket.com/albums/jj93/iansturges/hickorybow2.jpg)
This is the bow, the tiller is not as good as it could have been as it started to de-laminate when I was tillering it, so I lost quiet a bit of weight I ended up sacrificing the tiller to keep the weight up.
-
the tiller is the most important part, what layers delaminated? you might just want to try re laminating themand then tillerng it from there, i would hate to see this bow delaminate on you while you are shooting it, with a bow this weight that could be very painful
good luck
noel
-
"the tiller is not as good as it could have been"
??? It must be the photo then, cause that bow looks spot on tiller wise to me. I do understand photos can be very inaccurate and hide/or create tiller problems. But I couldn't see a hinge/problem with that tiller in the pic with a freaking microscope, :). I think you did a nice job.
EDIT: Wait, now I see it, bottom limb looks too weak (or bending too much, could be the way your drawing it.). I would recommend flipping the bow and making the top limb the bottom for the time being if that is infact the case. Could just the way your drawing it though. Very nice bow either way!
-
Thanks for the input on my stave guys :) My only tools right now are a pocketknife and a crummy rasp so I apologize if I don't post progress pics very often. Adb, I now have a shorter string and I'm gonna look into getting a tillering tree soon. Also, I have another warbow #110@30 that is the same lam combo as this one and it has performed fantastic for over a year, so I remain very hopeful for this one.
-
wow! for only those tools this is very good, the tiller dos look better in the second picture and if you've had success with the combo before, than theres no reason to doubt it
good luck
noel
-
Advice to get a proper length string on is good. A long string can tend to make outer limbs and tips look stiff. When the low brace height string is put on you them find you have weak outer limbs!
Get a string on that gives about 5 inches brace height and then just check the bend, exercise it a very little and work for an even bend at brace and work from there.
Good luck,
Mark in England
-
Sorry I haven't kept this thread very active lately. Been focusing on finding a job and such.
Anyways, I have made myself a tillering stick and fashioned a shorter tillering string as advised. Im now ready to get back to work on this stave. Previously I had been taking videos of the tiller in. However, there was very little difference from video one to video eight. So, I halted progress until I could get a tillering stick and appropriately sized string. Both of which I have now!
So, this video is my eighth tiller video as explained above. I just thought Id show you guys where Im at now and hopefully I'll have it finished soon!
http://www.youtube.com/watch?v=omsppS5FDsU (http://www.youtube.com/watch?v=omsppS5FDsU)
-
Bows are more important than Jobs ::)
The outer 18-24" could do with bending more on both limbs, and I would be careful with the left limb in the picture just make sure no hinge develops there, its going well so far keep us posted.
-
Ok, so I've got the stave bending evenly. The string is as long as the stave and was pulled to 16". What now? Do I scrape along the entire length of the bow? How do I proceed? Thanks a million!
-
If you think it will (or post a picture) get it to a low brace 4" but be careful if you haven't tillered enough many bows break while stringing for the first time.
You have got to be sure that you've got the stave near the final dimensions of the 130lb any excess will get crushed and will make it difficult to get a good weight, that is apart from the tips as you can get the last 18" flexing later on.
-
Still working on this tri-lam warbow. It has been a few months since I worked on it last and boy is it a doozy, haha! Here is a quick video showing the current bend. It still needs plenty of work in the mid-limb area to the tips. The upper limb is on the right hand side of the screen and doesn't appear to bend as much as the lower limb. The lower limb in fact looks like it might be developing a hinge next to my hand.
My next goal is to build a tiller tree with a good strong pulley system. I am working on this bow purely from making short videos like these and using a mirror for floor tillering.
Anyways, any help is appreciated! I have a good idea of what to do and of course a tiller tree is really going to help once I get that built.
Oh! I am hoping to get anything over #90@32". Originally I was shooting for #130@32" but since I haven't been shooting warbows for awhile and since this stave was on the thinner side I though #130 might be pushing it.
http://www.youtube.com/watch?v=YjxccjyJSYo (http://www.youtube.com/watch?v=YjxccjyJSYo)
-
looks pretty good, bu ti thin it needs some more bend in the right limb,looking good so far ;D, cant wait to see it spitting arrows
-
I'd say that it is a little stiff mid right limb.. The left limb is looking good...
Jon
-
Looking good Dag, I don't think you need to do much to it and to be honest I would be inclined to give it a low brace and see how it looks. Wood will need to be removed from some areas but don't both trying to chase a perfect long string tiller, get it on a short string as soon as you can.
-
Thanks for the comments guys!
I held up a CD to a still of the video and the lower limb actually looks pretty good and maybe is not hinging but rather the upper limb just needs more work.
I'll try and give it a brace this week Ian, I'm nervous, haha! Naw, warbowery is not for the faint of heart and I fear not :) The stave is looking and feeling like it is going to make it over my #90@32" minimum goal with no problem.
Bottom line is I need to get that tiller tree set up! haha!
Again, thanks for your input guys!