Primitive Archer

Main Discussion Area => Bows => Topic started by: ricktrojanowski on November 05, 2009, 06:36:58 am

Title: Heating Reflex into Yew Question
Post by: ricktrojanowski on November 05, 2009, 06:36:58 am

Never working with Yew before.  I was wondering if I can heat some reflex into it as I would with osage, with a heat gun and a caul ?

Title: Re: Heating Reflex into Yew Question
Post by: adb on November 05, 2009, 09:41:31 am

You can, but I've had better luck bending yew with steam, or boiling the tips for recurving.

Title: Re: Heating Reflex into Yew Question
Post by: Keenan on November 05, 2009, 10:30:08 am

Rick, Yew heat bends very well. I usually use Crisco and heat on dry wood or steam on green wood.  If you  are going to do extremely small tight recurves, steam would probably be best. This is one that I just did that was very deflexed stave  (6.5") and I just rolled the mid limb back. Dry heat with Crisco

(http://i30.photobucket.com/albums/c326/bornagainprimitve/IMG_0865.jpg)
(http://i30.photobucket.com/albums/c326/bornagainprimitve/IMG_0895.jpg)

Title: Re: Heating Reflex into Yew Question
Post by: NOMADIC PIRATE on November 05, 2009, 01:21:55 pm

Beautifull job Keenan,

Title: Re: Heating Reflex into Yew Question
Post by: Keenan on November 05, 2009, 01:59:25 pm

 Thanks Manny, It's just tilered on a long string so far, But I'll run a thread on this one soon I hope  ;D.

Title: Re: Heating Reflex into Yew Question
Post by: Rich Saffold on November 05, 2009, 03:23:07 pm

That looks sweet Keenan!

Title: Re: Heating Reflex into Yew Question
Post by: AllanM on November 05, 2009, 04:04:24 pm

Nice looking bow Keenan. Being from the UK I'm not familiar with Crisco and how it is used in the process. Could you explain please. Cheers, Allan

Title: Re: Heating Reflex into Yew Question
Post by: Keenan on November 05, 2009, 04:27:06 pm

Allen, Crisco is just a brand of lard. Basically heat the wood a little and sub some on with a rag and it helps keep to much moisture from being lost while heating.  It soaks in slightly but only the minimal surface. You don't want to do it on a bow that is nearly finished or you might have to sand it way past your desired weight.  I'll will usually do it at or just before floor tiller stage.

Title: Re: Heating Reflex into Yew Question
Post by: ricktrojanowski on November 05, 2009, 08:14:04 pm

Thanks for the info Keenan.  That is a sweet looking bow.  The stave is nice and dry so I'll go with some dry just to put a bit of deflex into it. 

Title: Re: Heating Reflex into Yew Question
Post by: radius on November 07, 2009, 09:47:01 am

i really like that bow too, Keenan, get busy and let's see it finished!  Love that humpy bumpy yew wood.  I sure hope my ride shows up.  He's supposed to be here in half an hour to go on a quest for yew.  Logs are waiting.  I've been waiting.  Here's a hoping.

Title: Re: Heating Reflex into Yew Question
Post by: Pat B on November 07, 2009, 10:12:52 am

AlanM, I use olive oil and a heat gun for all my bow wood bending with good results. I've only made a few yew bows(one a 95#@30" war bow) and used this method for lining things up. I believe any oil, grease or lard will work to help prevent scorching.