Primitive Archer
Main Discussion Area => Bows => Topic started by: Grunt on August 27, 2009, 09:29:23 pm
-
Just completed a hot box made with all recycled material. Last winter I had a hard time getting it above 65 degrees in my studio so glue ups were a problem. This box should fix that. four 100 watt bulbs for heat inside measurements are 76" long 20" deep 20" wide with foil backed insulation board. The form is a reflex/deflex out of the TBB.
[attachment deleted by admin]
-
Very nice job, is there any fire danger with your design I wonder?
-
Nice hot box. Very similar to mine. I got my design from Bingham Projects. I have a thermostat installed that will limit my temp to 186deg. Plenty enough for glue-ups. Got it from Bingham's and for only a few bucks. One other thing I did with my box was to add 2, 1" holes; one at the top of one end and one at the bottom of the other end. For cooking glue-ups I plug the holes but for drying wood I open the holes to allow air circulation and aid the drying process.
You can get the temp down to below 100degs by using one 60w bulb and this works well for drying wood or maintaining constant m/c in wood.
-
why would there be a fire danger?
because of the plywood case?
nope,if there was a fire danger the staves would catch first as the foil backed insulation keeps the heat in quite well
i have one very similar,no wood case(yet)but same foil backed insulation,with three 150w bulbs,i have mine hooked up to a rheostat so i can
adjust the out put and temp inside the box
yup i gotta up grade mine to have the sweet wood case
-
Pat, I'll be boring 1" holes this morning. I'm going to do a dry run today. I've got a meat thermometer inserted through the side and I am shooting for 150', I'll post the results. Might have to go with a thermostat. Thanks for the tips.
-
Another little trick is to add a small fan inside for those drying times. Helps speed up the drying time. The one I use is an electronic equipment cooling fan about 4" square in size.
You will be surprised how hot it will get with 4, 100w bulbs.
-
I also put a rheostat switch so I can adjust the temperature by dimming the bulbs. I only have 3 bulbs and can take it as low as I want.I haven't done any glue up,just mainly use for drying wood and don't want it that hot about 90 will do that. I have had it up to about 140. Very nice job on that one. :)
Pappy
-
My box is very similar to this. I have a rheostat in mine with a meat thermometer about a third way up from the bottom at one end. 3-150 watt bulbs will give me about 200deg. at full power. For drying slats, I turn out 2 of 'em and run one at about half power for 90-100deg.
I don't think I have a fire hazard as I sealed the joints with foil duct tape (much stronger than reg. duct tape and won't melt - don't ask! ::)) The wood case stays absolutely cool to the touch , just slightly warm directly over the light sockets where I couldn't put any insulation. They can bury me in this thing! :o Nearly half a bottle of wood glue and a couple pounds of sheetrock screws!!!
BTW, really nice form! I gotta check my books for that one!
-
Well I got 135 degrees with the 100 watt bulbs. I'll add one 150 watt bulb and see if I can bump it up 20 for glue curing. Great support guys, thanks.
-
I can just imagine Dracula sitting up in that on a dark winter's night >:D
-
Nice fancy heat box. Mine is leftover wood I pulled out of a dumpter. I wanted mine for a drying box mainly.
I wonder if you put a blanket or sleeping bag over it like Torges does if you could get 180F?
-
That's a good looking hotbox. I'm surprised that you're no getting hotter temps with those four hundred-watters.
-
What type of wire/size are you guys using to wire up the lamp-holders ?
-
Got 160' with two 150 watt and two 100 watt. I put in a 800 watt dimmer switch so I can bump it down to dry wood. Weatherstriped the lid and went over all inside seams with foilbacked tape and bored a high and a low 11/4" hole for air flow when drying wood. Wire size 16/2 because all wiring is outside the box and the porcelain fixtures are mounted on metal surface mount boxes screwed to the inside lid.
-
Great job Grunt, that oughta keep your boots dry as well. ;D
-
Great job Grunt, that oughta keep your boots dry as well. ;D
I never thought of that! ::) I am tired of pulling on old wet squishy hunting boots in the morning too. Dang good idea!!