Author Topic: Gizmo question  (Read 2119 times)

0 Members and 1 Guest are viewing this topic.

Offline Ricardovanleeuwen

  • Member
  • Posts: 403
Gizmo question
« on: May 21, 2020, 06:33:01 am »
I want to make a Gizmo but do a longer/shorter Gizmo makes Anny difference in hoe sinsitive It is?

Offline Eric Krewson

  • Member
  • Posts: 5,432
Re: Gizmo question
« Reply #1 on: May 21, 2020, 07:10:17 am »
I have made hundreds of them, 6" is the most usable length. Some folk make them shorter, I have made a few shorter but always go back to the 6" ones.

Offline bassman

  • Member
  • Posts: 962
Re: Gizmo question
« Reply #2 on: May 21, 2020, 06:09:23 pm »
I use a 6 inch Gizmo along with a 4 inch piece of wood with a screw through the middle that will scratch the wood were it  needs to come off the belly. One will work better than the other at times.

Offline Ricardovanleeuwen

  • Member
  • Posts: 403
Re: Gizmo question
« Reply #3 on: May 21, 2020, 11:40:18 pm »
Oke so i Just have to find what works best for me somewhere in the 6 inch range. I did try with a screw but i preffer a pencil because its more visible

Offline bassman

  • Member
  • Posts: 962
Re: Gizmo question
« Reply #4 on: May 22, 2020, 04:15:28 am »
You can turn the stave to the light, and see all the scratch marks ,and pencil them.

Offline Ricardovanleeuwen

  • Member
  • Posts: 403
Re: Gizmo question
« Reply #5 on: May 22, 2020, 07:41:13 am »
Didn't think of that thanks

Offline Pat B

  • Administrator
  • Member
  • Posts: 37,633
Re: Gizmo question
« Reply #6 on: May 22, 2020, 07:59:04 am »
The Gizmo design made by Eric has been proven to be a good wood bow building and tillering device by many bow builders. I have one of Eric's Gizmos that I use and find it to be a very helpful tool. Folks have been using their scrapers or a 6" ruler to show the variation in in bends for years now but Eric's design has one added feature, the adjustable pencil that shows you where to remove wood for a consistent bend.
Make the most of all that comes and the least of all that goes!    Pat Brennan  Brevard, NC

Offline bassman

  • Member
  • Posts: 962
Re: Gizmo question
« Reply #7 on: May 22, 2020, 08:04:05 am »
No doubt about that , but the scraper will tell how how deep to take the wood off in certain tight places which has been and additional aid to me any how.

Offline Pat B

  • Administrator
  • Member
  • Posts: 37,633
Re: Gizmo question
« Reply #8 on: May 22, 2020, 08:15:55 am »
I like giving credit where credit is due. Eric has been very generous with his Gizmo not only with folks here but donates lots to support
St Jude's Children's Hospital.
Make the most of all that comes and the least of all that goes!    Pat Brennan  Brevard, NC

Offline bassman

  • Member
  • Posts: 962
Re: Gizmo question
« Reply #9 on: May 22, 2020, 08:43:03 am »
I give him all the credit in the world. The scraper deal is just some thing I mentioned in case some one may want to try it to see if it also helps them. Never a knock on Eric. Was not my purpose of mentioning the scraper. The scraper is what I used until I found out about Eric's Gizmo. Then I quickly built one, and use it a lot but, I still use the scraper at times  along with the Gizmo.If you are happy with just using the Gizmo that is great, and it is a great tool for tillering.

Offline Eric Krewson

  • Member
  • Posts: 5,432
Re: Gizmo question
« Reply #10 on: May 22, 2020, 02:05:42 pm »
I have 15 gizmos up for bids on the Trad Gang St Jude auction right now. The bidding starts this evening around 6PM EST.

All of the gizmos are fancy, 11 are curly maple, 4 are exhibition grade walnut signed by me, like this one;


 

Offline Ricardovanleeuwen

  • Member
  • Posts: 403
Re: Gizmo question
« Reply #11 on: May 23, 2020, 02:27:31 pm »
Is there a reason that they are tapered from thiddle tocboth ends?

Offline Bob Barnes

  • Member
  • Posts: 942
Re: Gizmo question
« Reply #12 on: May 23, 2020, 02:46:46 pm »
I think it helps when working up towards the tips on the bow and it makes it less likely you will hit the string...
Seems like common sense isn't very common any more...

Offline Eric Krewson

  • Member
  • Posts: 5,432
Re: Gizmo question
« Reply #13 on: May 23, 2020, 04:42:44 pm »
This was the first one I made years ago, not much string clearance when you ran it up the limbs. I used screws to hold the pencil in place.

Offline NewBowyer

  • Member
  • Posts: 105
Re: Gizmo question
« Reply #14 on: May 24, 2020, 07:45:20 am »
As a new bowyer I can verify that this gizmo helped me immensely with tillering. I also love it for its ingenious simplicity, something I always prefer to complexity.