« previous next »
Pages: [1]

Author Topic: Small diameter osage  (Read 2332 times)

0 Members and 1 Guest are viewing this topic.

FAW

  • Guest
Small diameter osage
« on: June 30, 2017, 09:37:24 pm »
Have not been here for awhile for a lot of reasons, however, renewing my attempt to complete a first ( for me ) osage bow. The victim stave appears to be half of a small diameter section which was formerly a 3" tree trunk, split down the centre. When starting to remove the first growth ring, I suddenly realized if I attempt to remove layers to obtain a flat back there will not be enough wood to properly provide a handle area. Does one have to decrown or can this be made into a workable bow without decrowning. It is currently 68" long, with a tight grain pattern and a good ratio of light to dark layers, albeit very close together. I have completed some whitewood bows and a composite with limited success and am hoping for an osage - sure wished it was a different piece of osage though.
Logged

Offline BowEd

  • Member
  • Posts: 9,390
  • BowEd
Re: Small diameter osage
« Reply #1 on: June 30, 2017, 09:50:04 pm »
Small diameter osages' like sapling bows are some of the best resilient osage bows out there.You should'nt feel disappointed for the diameter of your stave.You should have enough for a stiff handle yet.Sounds like a perfect plan to me.
Logged
BowEd
You got to stand for something or you'll fall for anything.
Ed

Offline Pat B

  • Administrator
  • Member
  • Posts: 37,633
Re: Small diameter osage
« Reply #2 on: June 30, 2017, 10:18:57 pm »
I love small diameter osage bows. I've made 4 or 5 of them and they all performed well. With the high crown I like to keep the belly flat. You don't have to remove the sapwood either. Just get the bark off and shape the bow.
Logged
Make the most of all that comes and the least of all that goes!    Pat Brennan  Brevard, NC

Offline PEARL DRUMS

  • Member
  • Posts: 14,079
  • }}}--CK-->
Re: Small diameter osage
« Reply #3 on: July 01, 2017, 06:51:43 am »
I couldn't agree more with Ed and Pat. Small stuff makes great bows in nearly every good bow wood. I just made an elm bow that came from a 2.5" or so pole. In the handle area you can always glue a riser block on to build it up. Just stay away from the center 12" while you roung it out and get it floor tillered. You don't need much depth to stop the bending.
« Last Edit: July 03, 2017, 07:25:44 am by PEARL DRUMS »
Logged
Only when the last tree has died and the last river has been poisoned and the last fish has been caught will we realize we cannot eat money.

Offline George Tsoukalas

  • Member
  • Posts: 9,425
    • Traditional and Primitive Archers
Re: Small diameter osage
« Reply #4 on: July 01, 2017, 09:11:25 am »
One of my best osage bows I made was from a 1 inch diameter osage sapling/ sucker that Rusty Craine gave me at Mojam in 2003.

If you don't have enough heartwood you can leave a layer  or 2 of sapwood.

If the stave is heavily crowned leave it a an inch or 2 longer. You don't have to decrown.

Jawge
« Last Edit: July 03, 2017, 08:19:09 am by George Tsoukalas »
Logged
Set Happens!
If you ain't breakin' you ain't makin!

FAW

  • Guest
Re: Small diameter osage
« Reply #5 on: July 01, 2017, 09:51:12 am »
That is a real relief to me. I have had this stave for a few years and decided it was time to do something with it and been puzzling over it for the past two days. Work will continue and with the expert advice here, it may become a bow.
Logged
Pages: [1]
« previous next »