« previous next »
Pages: [1] 2

Author Topic: Bringing the heat, preferred methods?  (Read 5739 times)

0 Members and 1 Guest are viewing this topic.

Offline Ippus

  • Member
  • Posts: 137
Bringing the heat, preferred methods?
« on: October 23, 2016, 05:20:39 pm »
I'm in the process of peeling some wild rose shoots I harvested last fall, and they're all going to need some degree of straightening.

What's your preferred heat-straightening method?
Steam? Just use a kettle?

Dry?
I don't have a propane torch, but I do have a liquid-fuel Coleman stove (afaik, the fuel is cheaper than propane if it'll be burning awhile). How hot would a blow-dryer have to be to be effective?

When deciding wet vs. dry heat, does it matter if you're in a more or less humid climate? i.e., is there more concern about adding moisture to the shaft if the climate's already humid?
Logged
"There is nothing quite so gentle, deep, and irrational as our running — and nothing quite so savage and so wild.” Bernd Heinrich

Offline helmet

  • Member
  • Posts: 168
Re: Bringing the heat, preferred methods?
« Reply #1 on: October 23, 2016, 06:55:23 pm »
On the few rose shafts I made they straighted fairly easily with just a candle. I have never tried using steam on arrow shafts so i am no help there.
Rose makes a good arrow.
Logged

Offline Pat B

  • Administrator
  • Member
  • Posts: 37,618
Re: Bringing the heat, preferred methods?
« Reply #2 on: October 23, 2016, 08:11:24 pm »
I've not made rose arrows but with cane and hardwood shoots I use the kitchen gas stove. Have the burner on low and keep the shaft moving back and forth while rotating it. I like using dry heat because it tempers the wood(cane) as you straighten it. When I have the shaft straight I start at one end heating and rotating as I move down the shaft. WARNING...watch out for the steam coming out the far end. At a few points along the shaft I will scorch the wood so it has camo effect. Once I've done this I hand straighten the shaft if necessary then lay it on a flat surface to completely cool completely.
Logged
Make the most of all that comes and the least of all that goes!    Pat Brennan  Brevard, NC

Offline bjrogg

  • Member
  • Posts: 10,997
  • Cedar Pond
Re: Bringing the heat, preferred methods?
« Reply #3 on: October 23, 2016, 10:22:49 pm »
I always use dry heat, I have used candles, propane camp stove, kitchen electric stove, even coals from a campfire. It usually takes me 3 sessions per arrow shaft minimum. I get big curves out 1st let cool then get more fussy next 2 sessions. I don't think steam would work that great you kinda want Something that beats a localized spot. At least that's what works for me.
Bjrogg
Logged
A hot cup of coffee and a beautiful sunrise

Offline Pat B

  • Administrator
  • Member
  • Posts: 37,618
Re: Bringing the heat, preferred methods?
« Reply #4 on: October 24, 2016, 12:05:15 am »
I do like Bj and straighten in sessions with cooling between.
Logged
Make the most of all that comes and the least of all that goes!    Pat Brennan  Brevard, NC

Offline BowEd

  • Member
  • Posts: 9,390
  • BowEd
Re: Bringing the heat, preferred methods?
« Reply #5 on: October 24, 2016, 02:39:34 am »
Dry heat over the chimney of a lamp does the trick for me.
Logged
BowEd
You got to stand for something or you'll fall for anything.
Ed

Offline loon

  • Member
  • Posts: 1,307
Re: Bringing the heat, preferred methods?
« Reply #6 on: October 24, 2016, 05:40:28 am »
Heat gun.. relatively low setting, 550 or at most 750F? Definitely not 950, then they just seem to burn and break
Logged

Offline Pappy

  • Global Moderator
  • Member
  • Posts: 32,137
  • if you have to ask you wouldn't understand ,Tenn.
Re: Bringing the heat, preferred methods?
« Reply #7 on: October 27, 2016, 07:21:06 am »
Heat gun most of the time, over the fire or hot coals if I am just setting around the fire doing nothing and really feeling Primitive. ;) :) :) It's fun sometime to straighten and scrape on arrows when just setting around talking. :) Very relaxing. :)
 Pappy
Logged
Clarksville,Tennessee
TwinOaks Bowhunters
Life is Good

Offline PEARL DRUMS

  • Member
  • Posts: 14,079
  • }}}--CK-->
Re: Bringing the heat, preferred methods?
« Reply #8 on: October 28, 2016, 07:23:17 am »
Never made a wild rose shaft, but made some viburnum and various canes. I always use a gas stove burner on low. Im amazed how little heat it requires to easily bend shafts.
Logged
Only when the last tree has died and the last river has been poisoned and the last fish has been caught will we realize we cannot eat money.

Offline Redhand

  • Member
  • Posts: 704
  • Marlen Murdock PM109458
Re: Bringing the heat, preferred methods?
« Reply #9 on: October 28, 2016, 09:26:52 am »
I use a hot plate and a arrow straightener made out of soapstone.
« Last Edit: October 28, 2016, 05:42:46 pm by Redhand »
Logged
Northern Ute

Offline Thunder

  • Member
  • Posts: 240
Re: Bringing the heat, preferred methods?
« Reply #10 on: October 28, 2016, 10:33:05 am »
A blow dryer produces more than enough heat be effective in straitening a wild rose shaft.
I look forward to seeing some finished wild rose arrows.

Cheers
Thunder
Logged
"The two most important days in your life are the day you are born...and the day you find out why."  Mark Twain

Offline DC

  • Member
  • Posts: 10,396
Re: Bringing the heat, preferred methods?
« Reply #11 on: October 28, 2016, 02:36:39 pm »
Quote from: Redhand on October 28, 2016, 09:26:52 am
I use a hot plate arrow straightener made out of soapstone.

Do you think we could see a picture? Thanks
Logged

Offline Ippus

  • Member
  • Posts: 137
Re: Bringing the heat, preferred methods?
« Reply #12 on: October 28, 2016, 03:19:43 pm »
Quote from: DC on October 28, 2016, 02:36:39 pm
Quote from: Redhand on October 28, 2016, 09:26:52 am
I use a hot plate arrow straightener made out of soapstone.

Do you think we could see a picture? Thanks

I second that!
Logged
"There is nothing quite so gentle, deep, and irrational as our running — and nothing quite so savage and so wild.” Bernd Heinrich

Offline loon

  • Member
  • Posts: 1,307
Re: Bringing the heat, preferred methods?
« Reply #13 on: October 28, 2016, 04:09:12 pm »
I want soapstone...
Logged

Offline Redhand

  • Member
  • Posts: 704
  • Marlen Murdock PM109458
Re: Bringing the heat, preferred methods?
« Reply #14 on: October 28, 2016, 04:31:34 pm »
When I get home I will post some pics.
Logged
Northern Ute
Pages: [1] 2
« previous next »