« previous next »
Pages: 1 2 [3] 4 5 ... 28

Author Topic: My board bow (build along?)  (Read 86842 times)

0 Members and 1 Guest are viewing this topic.

Offline Stick Bender

  • Member
  • Posts: 2,003
Re: My board bow (build along?)
« Reply #30 on: July 06, 2016, 03:50:35 pm »
Good to see you back I'm following your build hope you get your saw fixed
Logged
If you fear failure you will never Try !

Offline Marin

  • Member
  • Posts: 461
Re: My board bow (build along?)
« Reply #31 on: July 07, 2016, 09:53:58 pm »
Got the saw working again and was able to cut the profile with a skill saw. I will try cutting the belly taper on Saturday. I tried not cutting on the lines but sometimes I would get really close. For the belly taper, is there something besides a bandsaw I can use to cut it?  I have a jigsaw but am unsure if I can keep it straight enough.
Logged

Offline bubby

  • Member
  • Posts: 11,054
Re: My board bow (build along?)
« Reply #32 on: July 07, 2016, 10:39:17 pm »
You can do all the belly rough removal with a good rasp
Logged
failure is an option, everyone fails, it's how you handle it that matters.
The few the proud the 27🏹

Offline Knotty

  • Member
  • Posts: 504
  • Don't regret your past, learn from it.
Re: My board bow (build along?)
« Reply #33 on: July 08, 2016, 04:47:02 pm »
I usually use a rasp for rough material removal, a couple files and different grits of sandpaper.
Good luck!
Logged
~Isaia

Offline Stick Bender

  • Member
  • Posts: 2,003
Re: My board bow (build along?)
« Reply #34 on: July 08, 2016, 05:53:18 pm »
I use all the above pluss I use scrapers a lot leaves a verry smoth surfice I pick up paint scrapers from good will for $2 they work great  also 38 grit sanding belts cut & glued on a peace of lumber works really well poor mans rasp , but when I get close to where I want I always swith to scrapers & finer grit sand paper
Logged
If you fear failure you will never Try !

Offline Marin

  • Member
  • Posts: 461
Re: My board bow (build along?)
« Reply #35 on: July 10, 2016, 05:08:33 pm »
Hey I just measured my cut out board I was going to glue on for the handle section and I found that I cut it about 2/16 of an inch shorter than the wanted 8 inches. Should I recut another piece or does a difference like this matter?
Logged

Offline penderbender

  • Member
  • Posts: 733
  • island life...
Re: My board bow (build along?)
« Reply #36 on: July 10, 2016, 05:21:22 pm »
A 1/16 on either end won't matter.
Logged

Offline Knoll

  • Member
  • Posts: 3,016
  • Mikey
Re: My board bow (build along?)
« Reply #37 on: July 10, 2016, 06:45:32 pm »
Wouldn't give it another thought. March on.
Logged
... alone in distant woods or fields, in unpretending sproutlands or pastures tracked by rabbits, even in a bleak and, to most, cheerless day .... .  I suppose that this value, in my case, is equivalent to what others get by churchgoing & prayer.  Hank Thoreau, 1857

Offline Marin

  • Member
  • Posts: 461
Re: My board bow (build along?)
« Reply #38 on: July 10, 2016, 11:23:19 pm »
Do you guys lightly rasp before gluing your handle to your bow? I heard some people do that and others lightly rasp and then glue both sides, let those sides dry, and then glue it on. I'm going to lightly rasp my handle and bow (where the handle is going to be at) before gluing it. If anyone concurs, please say.
Logged

Offline penderbender

  • Member
  • Posts: 733
  • island life...
Re: My board bow (build along?)
« Reply #39 on: July 10, 2016, 11:31:01 pm »
I'd go with some course paper. Rasps can ruin things in a hurry.  You don't wanna rough it up too much.
« Last Edit: July 11, 2016, 01:37:56 am by penderbender »
Logged

Offline bubby

  • Member
  • Posts: 11,054
Re: My board bow (build along?)
« Reply #40 on: July 10, 2016, 11:40:29 pm »
I just sand it if you are using tb glues they aren't gap filling so you want an tight fit
Logged
failure is an option, everyone fails, it's how you handle it that matters.
The few the proud the 27🏹

Offline Marin

  • Member
  • Posts: 461
Re: My board bow (build along?)
« Reply #41 on: July 11, 2016, 07:43:31 pm »
Okay,glued on handle after a light sanding. When gluing it, it was a little harder than I thought. I have clamps of 3 different sizes so the thing was sliding around while I was trying to clamp it down but I was able to get it into the spot I wanted. Hope it turns out well. I don't think I clamped it too hard  :-\
Logged

Offline Lumberman

  • Member
  • Posts: 335
Re: My board bow (build along?)
« Reply #42 on: July 11, 2016, 07:55:49 pm »
Sweet! What thickness is the board at? The limbs that is
Logged

Offline Marin

  • Member
  • Posts: 461
Re: My board bow (build along?)
« Reply #43 on: July 11, 2016, 08:01:39 pm »
I have not reduced the belly thickness yet.
Logged

Offline Marin

  • Member
  • Posts: 461
Re: My board bow (build along?)
« Reply #44 on: July 12, 2016, 10:39:48 pm »
Just got in from cuttin fthe handle. I I clamped the handle an d checked which made me a little worried because on one side I saw a little bit I of a gap :-[
I used a jigsaw to roughly cut it and I think it has rendered me half deaf  ;)
Here's how it looks. I checked the edges. I guess the gap,was only at the front. What do you guys think of the glue job?
Hopefully I will start rasping the belly and handle tommorow but maybe not.
Ill get back to you guys
Logged
Pages: 1 2 [3] 4 5 ... 28
« previous next »