« previous next »
Pages: [1]

Author Topic: What might be done with these components?  (Read 2462 times)

0 Members and 1 Guest are viewing this topic.

Offline Knoll

  • Member
  • Posts: 3,016
  • Mikey
What might be done with these components?
« on: August 24, 2015, 09:36:15 am »
Seeking ideas on how to use all or some of following 3 components to form a new bow.

thin piece of jatoba. 63" length x  just 0.3" thick . . . front profile is cut . . . 1.5" wide to 15 1/2" from tips, then taper to 1/2.
thicker hard maple slat.  67" x 1 3/4 x .45
very thin pc of hard maple.  63 1/2 x 1 3/4 x .15

Draw weight/length objective is 45-47 @ 25".

Whatcha recommend?
Logged
... alone in distant woods or fields, in unpretending sproutlands or pastures tracked by rabbits, even in a bleak and, to most, cheerless day .... .  I suppose that this value, in my case, is equivalent to what others get by churchgoing & prayer.  Hank Thoreau, 1857

Offline Badger

  • Member
  • Posts: 8,124
Re: What might be done with these components?
« Reply #1 on: August 24, 2015, 10:09:19 am »
  jatoba is a nice belly wood but requires absolutely perfect tillering or it will chrysal. The maple can be used as core and backing if the grain is straight. maple is also a decent belly wood but not one of my top choices.
Logged

blackhawk

  • Guest
Re: What might be done with these components?
« Reply #2 on: August 24, 2015, 10:17:41 am »
Yup...maple backed jatoba with a maple core tri lam....since the jatoba is kinda thin id make it a slight bend in the handle at the very least...no gluing on a stiff handle. Make it no wider than 1 1/8". Tiller it good.
Logged

Offline bubby

  • Member
  • Posts: 11,054
Re: What might be done with these components?
« Reply #3 on: August 24, 2015, 12:21:09 pm »
Quote from: blackhawk on August 24, 2015, 10:17:41 am
Yup...maple backed jatoba with a maple core tri lam....since the jatoba is kinda thin id make it a slight bend in the handle at the very least...no gluing on a stiff handle. Make it no wider than 1 1/8". Tiller it good.




X2😉
Logged
failure is an option, everyone fails, it's how you handle it that matters.
The few the proud the 27🏹

Offline Knoll

  • Member
  • Posts: 3,016
  • Mikey
Re: What might be done with these components?
« Reply #4 on: August 24, 2015, 02:06:27 pm »
Ok, flex-in-the-handle tri lam will be the plan.
And narrow width to 1 1/8".
Glue-in reflexed limbs or leave flat? The thicker pc of maple has a bit of reflex 'cause it was once glued to red elm backing.
I usually do 6" long glued-on static flipped tips. OK, or decreased length of working limb a risk?
Logged
... alone in distant woods or fields, in unpretending sproutlands or pastures tracked by rabbits, even in a bleak and, to most, cheerless day .... .  I suppose that this value, in my case, is equivalent to what others get by churchgoing & prayer.  Hank Thoreau, 1857

Offline snedeker

  • Member
  • Posts: 907
Re: What might be done with these components?
« Reply #5 on: August 26, 2015, 03:01:11 pm »
I'd use the jatoba as the core, the thin maple as backing, and the thick maple as belly.  63" long, 1.5 wide, rigid handle with 8" fade area.

Dave
Logged

Offline Pat B

  • Administrator
  • Member
  • Posts: 37,633
Re: What might be done with these components?
« Reply #6 on: August 26, 2015, 06:35:04 pm »
Are you just trying to sneak up on us, Dave.  ;D    Haven't seen you around for quite a while. Hope all I well with you.

  Pat
Logged
Make the most of all that comes and the least of all that goes!    Pat Brennan  Brevard, NC

Offline snedeker

  • Member
  • Posts: 907
Re: What might be done with these components?
« Reply #7 on: August 26, 2015, 06:46:59 pm »
I decided to look in and couldn't resist the issue of the jatoba and maple.   I'm well and hope you and all the old buddies are too
Logged

Offline Knoll

  • Member
  • Posts: 3,016
  • Mikey
Re: What might be done with these components?
« Reply #8 on: August 29, 2015, 06:07:56 pm »
Quote from: blackhawk on August 24, 2015, 10:17:41 am
Yup...maple backed jatoba with a maple core tri lam....since the jatoba is kinda thin id make it a slight bend in the handle at the very least...no gluing on a stiff handle. Make it no wider than 1 1/8". Tiller it good.

Jatoba is glued to the thicker maple slat. Total thickness of the 2 is about .79". Limb width is a bit greater than 1 1/8" until 12" from tips, and then taper to 1/2". This sucker is STIIIIFFF.

Move beginning of taper further toward middle, or reduce thickness of maple, or both?
Logged
... alone in distant woods or fields, in unpretending sproutlands or pastures tracked by rabbits, even in a bleak and, to most, cheerless day .... .  I suppose that this value, in my case, is equivalent to what others get by churchgoing & prayer.  Hank Thoreau, 1857

Offline Onebowonder

  • Member
  • Posts: 1,495
Re: What might be done with these components?
« Reply #9 on: August 29, 2015, 06:17:22 pm »
Yes, ...both.

OneBow
Logged
Pages: [1]
« previous next »