« previous next »
Pages: [1]

Author Topic: Handle goes pop! Remedies sought  (Read 3331 times)

0 Members and 1 Guest are viewing this topic.

Offline Knoll

  • Member
  • Posts: 3,016
  • Mikey
Handle goes pop! Remedies sought
« on: June 09, 2015, 12:21:39 am »
Heated up the limbs to induce a bit of reflex.  Apparently got a bit too much heat too close to glue-on handle.  Pop!! at upper limb fade.  Am considering rasping block into rasp-dust and glue on another one.

But before going to all that work, are there other successful remedies?
Logged
... alone in distant woods or fields, in unpretending sproutlands or pastures tracked by rabbits, even in a bleak and, to most, cheerless day .... .  I suppose that this value, in my case, is equivalent to what others get by churchgoing & prayer.  Hank Thoreau, 1857

Offline osage outlaw

  • Member
  • Posts: 11,962
Re: Handle goes pop! Remedies sought
« Reply #1 on: June 09, 2015, 12:30:50 am »
Can you post a picture of it?
Logged
I started out with nothin' and I still got most of it left

Offline Knoll

  • Member
  • Posts: 3,016
  • Mikey
Re: Handle goes pop! Remedies sought
« Reply #2 on: June 09, 2015, 12:33:03 am »
Yep.  On the morrow.  Past bedtime.
Logged
... alone in distant woods or fields, in unpretending sproutlands or pastures tracked by rabbits, even in a bleak and, to most, cheerless day .... .  I suppose that this value, in my case, is equivalent to what others get by churchgoing & prayer.  Hank Thoreau, 1857

Offline bowmo

  • Member
  • Posts: 1,035
Re: Handle goes pop! Remedies sought
« Reply #3 on: June 09, 2015, 12:33:41 am »
I do a lot of fiberglass cloth wraps over my billet z-splices that end up hidden under the grip wrap. I really do them out of paranoia, but if you got some epoxy in the lift and clamped it and then did that it could work. It's hard to say without a pic of your bow tho.
Logged

Offline bubby

  • Member
  • Posts: 11,054
Re: Handle goes pop! Remedies sought
« Reply #4 on: June 09, 2015, 12:42:25 am »
Are you sure you just didn't get it working to close to the handle?
Logged
failure is an option, everyone fails, it's how you handle it that matters.
The few the proud the 27🏹

Offline Dances with squirrels

  • Member
  • Posts: 1,222
Re: Handle goes pop! Remedies sought
« Reply #5 on: June 09, 2015, 06:30:50 am »
The heat probably got ya on that one, but usually, the cause and remedy is in prep and gluing practices.

Create nice gradual dips/fades, mate the pieces perfectly, surface prep them with a toothing plane blade, glue them with Smooth On cured with a little heat, and forget about it. No pedestals, no power lams, no sacrifice of working limb length. Done as described, you can let them bend into the glue joint some if ya like. They're not going anywhere.
Logged
Straight wood may make a better bow, but crooked wood makes a better bowyer

Offline PEARL DRUMS

  • Member
  • Posts: 14,079
  • }}}--CK-->
Re: Handle goes pop! Remedies sought
« Reply #6 on: June 09, 2015, 06:57:51 am »
Was it that maple bow Mike? 
Logged
Only when the last tree has died and the last river has been poisoned and the last fish has been caught will we realize we cannot eat money.

Offline Eric Krewson

  • Member
  • Posts: 5,412
Re: Handle goes pop! Remedies sought
« Reply #7 on: June 09, 2015, 09:02:01 am »
I agree, heat probably did in the glue on your handle.

If you want a handle that won't lift, glue on a couple of thin wood pieces on first and feather them into your limbs gracefully. The first one on this handle is only about 3/16" thick.


Logged

Offline Knoll

  • Member
  • Posts: 3,016
  • Mikey
Re: Handle goes pop! Remedies sought
« Reply #8 on: June 09, 2015, 09:59:40 am »
Yeak, Chris, it's that maple bow.  And, yes, problem is due to lousy pre-gluing prep.
GGood news is that it's lil block glued to back that lifted.  That block has been causing me headaches since day I put it on.
BBad news is that my camera is hiding ... AGAIN.
Planning to try Dvs & Eric suggestion.  Grind that sucker off & replace with several thin lams using Uni-Bond as adhesive.
Beginning to wonder if this one'll be finished before MoJam!  And hoping camera decides to come outta hiding soon.
Thanks, ya'll, for the inputs!!
« Last Edit: June 09, 2015, 10:02:51 am by Knoll »
Logged
... alone in distant woods or fields, in unpretending sproutlands or pastures tracked by rabbits, even in a bleak and, to most, cheerless day .... .  I suppose that this value, in my case, is equivalent to what others get by churchgoing & prayer.  Hank Thoreau, 1857

Offline PEARL DRUMS

  • Member
  • Posts: 14,079
  • }}}--CK-->
Re: Handle goes pop! Remedies sought
« Reply #9 on: June 09, 2015, 10:29:55 am »
Well I don't think your prep had anything to do with it. The "sandwich" riser design will pop again and again, sorry buddy. The suggestion to grind it off is a good one, however in order to get proper fades you will have to extend both directions at least an inch farther. That means you will lose 2" more of limb and Im not sure that bow has that to give, does it?
Logged
Only when the last tree has died and the last river has been poisoned and the last fish has been caught will we realize we cannot eat money.

Offline bowmo

  • Member
  • Posts: 1,035
Re: Handle goes pop! Remedies sought
« Reply #10 on: June 09, 2015, 10:34:05 am »
Put on a new handle with smooth-on or urac, wrap it with glass, and it will never move...no matter how close to the bend it is.
Logged

Offline bubby

  • Member
  • Posts: 11,054
Re: Handle goes pop! Remedies sought
« Reply #11 on: June 09, 2015, 10:50:33 am »
Mike is it rhick enough at the handle to use cork instead of a hard lam, if it is a board and full thickness in that area it will work
Logged
failure is an option, everyone fails, it's how you handle it that matters.
The few the proud the 27🏹

Offline Knoll

  • Member
  • Posts: 3,016
  • Mikey
Re: Handle goes pop! Remedies sought
« Reply #12 on: June 09, 2015, 11:14:35 am »
Quote from: bubby on June 09, 2015, 10:50:33 am
Mike is it rhick enough at the handle to use cork instead of a hard lam, if it is a board and full thickness in that area it will work
Yep, there's 3/4" limb thickness where this "block" on back would be located ... + handle block glued to belly.
« Last Edit: June 09, 2015, 11:24:21 am by Knoll »
Logged
... alone in distant woods or fields, in unpretending sproutlands or pastures tracked by rabbits, even in a bleak and, to most, cheerless day .... .  I suppose that this value, in my case, is equivalent to what others get by churchgoing & prayer.  Hank Thoreau, 1857

Offline PEARL DRUMS

  • Member
  • Posts: 14,079
  • }}}--CK-->
Re: Handle goes pop! Remedies sought
« Reply #13 on: June 09, 2015, 11:44:57 am »
Mike Id suggest using all cork if you want to continue with building up the front and back sides as started.
Logged
Only when the last tree has died and the last river has been poisoned and the last fish has been caught will we realize we cannot eat money.
Pages: [1]
« previous next »