« previous next »
Pages: [1]

Author Topic: bow design for a 56 inch bow  (Read 2767 times)

0 Members and 1 Guest are viewing this topic.

Offline Mooseman78

  • Member
  • Posts: 16
bow design for a 56 inch bow
« on: February 02, 2015, 11:20:57 pm »
I have a ash board that I want to make a 56 Inch bow out of and was wondering what would be the best design for this bow, the board is 56" long and 1 and 5/8 wide
Logged

Offline Blaflair2

  • Member
  • Posts: 2,042
Re: bow design for a 56 inch bow
« Reply #1 on: February 02, 2015, 11:28:11 pm »
Is it flat or quartersawn? Straight grain? Probly a bendy handle is best
Logged
Nothing ventured nothing gained

Offline Mooseman78

  • Member
  • Posts: 16
Re: bow design for a 56 inch bow
« Reply #2 on: February 02, 2015, 11:36:05 pm »
its a quarter sawn board and will most likely be sinew backed with im hopeing a bend in the handle design
Logged

Offline Blaflair2

  • Member
  • Posts: 2,042
Re: bow design for a 56 inch bow
« Reply #3 on: February 02, 2015, 11:46:52 pm »
I'd leave the width and make it a pyramid design. Others will chime in with more experience
Logged
Nothing ventured nothing gained

Offline Peacebow_Coos

  • Member
  • Posts: 811
Re: bow design for a 56 inch bow
« Reply #4 on: February 03, 2015, 12:04:15 am »
Sounds like you're on the road to an Ishi bow to me
Logged

Offline mwosborn

  • Member
  • Posts: 806
  • Mitch Osborn
Re: bow design for a 56 inch bow
« Reply #5 on: February 03, 2015, 12:05:48 am »
Draw length and weight?
Logged
Enjoy the hunt!  Mitch

Offline Mooseman78

  • Member
  • Posts: 16
Re: bow design for a 56 inch bow
« Reply #6 on: February 03, 2015, 01:09:46 am »
my draw is 28" and hoping to get at least 40-50lbs out of it
Logged

Offline RyanY

  • Member
  • Posts: 1,997
Re: bow design for a 56 inch bow
« Reply #7 on: February 03, 2015, 01:54:25 am »
What's your experience level? 28" and 40-50# is definitely feasable but it'll take some skill. I'd make it bend in the handle for sure. Sinew would be great for such a short bow. Maybe heat in some reflex first and then sinew it? I wouldn't go for a straight pyramid taper because you'll lose too much width in the outer limb. I'd keep it full width till mid limb at least but you could waist the handle to 1.25".
Logged

Offline Mooseman78

  • Member
  • Posts: 16
Re: bow design for a 56 inch bow
« Reply #8 on: February 03, 2015, 02:32:40 am »
my skill level is new so getting 40-50 might be hard for me, I didn't thnk a pyramid would be good like u say
Logged

Offline twilightandmist

  • Member
  • Posts: 198
    • My Etsy Shop:
Re: bow design for a 56 inch bow
« Reply #9 on: February 03, 2015, 03:46:18 pm »
ok i'll bite... as a beginner, i would suggest you go with a bending handle, and leave the handle wide, and leave the limbs as wide as you can for at least 2/3rds of the limbs, leaving it wider than usual even out to the tips. in my experience, a continuous bend style has proved successful for this type of bow. what i am trying to describe is something like this:

 this isn't ash, or a board, or backed, but it is quite short. the bend should be continuous and closer to circular than elliptical, in an attempt to strain the wood uniformly so no part has a larger amount of strain than any other, which could cause it to fail in that spot. Just my two cents, more experienced bowyers than I will likely have more valuable things to say on the matter.
Logged
My Longbow in one hand, My Colt 1860 Army in the other, and both feet in the past.

Offline mwosborn

  • Member
  • Posts: 806
  • Mitch Osborn
Re: bow design for a 56 inch bow
« Reply #10 on: February 03, 2015, 08:08:49 pm »
I think twilight gave you good advice.
Logged
Enjoy the hunt!  Mitch

Offline bradsmith2010

  • Member
  • Posts: 5,187
Re: bow design for a 56 inch bow
« Reply #11 on: February 03, 2015, 10:11:37 pm »
I like twilights bow as well, simple ,, and efficient ,,
Logged

Offline Mooseman78

  • Member
  • Posts: 16
Re: bow design for a 56 inch bow
« Reply #12 on: February 03, 2015, 11:15:47 pm »
thank u for our input Twilight I was thinking wide limbs for 2 thirds and wide handle
Logged
Pages: [1]
« previous next »