« previous next »
Pages: [1]

Author Topic: Update on (Lam bow)  (Read 2197 times)

0 Members and 1 Guest are viewing this topic.

Offline bow101

  • Member
  • Posts: 2,235
Update on (Lam bow)
« on: January 15, 2014, 01:40:07 pm »
In the process of building a bi-lam bow.  Have to now glue on a fade section.  How long should I make it.....? I was thinking 16" with a very gradual transition.   :-\
« Last Edit: January 23, 2014, 08:43:20 pm by bow101 »
Logged
"The privilege of a lifetime is being who you are."  Joseph Campbell

Offline Del the cat

  • Member
  • Posts: 8,322
    • Derek Hutchison Native Wood Self Bows
Re: Lam bow
« Reply #1 on: January 15, 2014, 01:46:09 pm »
No my bag, but that sounds like a lot of wasted limb to me. I'd have thought 4" gpip + 2" of fade either side equals 8"
Even if you want to make it a bit more symetrical you could go 4" grip, a couple of inches above the arrow pass and 2" either end for fades. which would be say 10".
I'm struggling to think what you need 16" in the middle of a bow for ... maybe writing shopping lists on it? >:D
Del
« Last Edit: January 15, 2014, 06:14:08 pm by Del the cat »
Logged
Health warning, these posts may contain traces of nut.

Offline bubby

  • Member
  • Posts: 11,054
Re: Lam bow
« Reply #2 on: January 15, 2014, 03:29:57 pm »
4" grip 2"-3" fades, that's ten inches max, and you might want a power lam, how thick is the main bow that is glued up
Logged
failure is an option, everyone fails, it's how you handle it that matters.
The few the proud the 27🏹

Offline bow101

  • Member
  • Posts: 2,235
Re: Lam bow
« Reply #3 on: January 15, 2014, 04:38:34 pm »
Quote from: bubby on January 15, 2014, 03:29:57 pm
4" grip 2"-3" fades, that's ten inches max, and you might want a power lam, how thick is the main bow that is glued up

Its maple roughly over 7/16"  X  1 1/2" wide, hope to end up with 66 NTN. 
Logged
"The privilege of a lifetime is being who you are."  Joseph Campbell

Offline bubby

  • Member
  • Posts: 11,054
Re: Lam bow
« Reply #4 on: January 15, 2014, 08:44:03 pm »
use a powerlam, make it several inches longer on each fade, if the riser is 10 go 14 on the powerlam
Logged
failure is an option, everyone fails, it's how you handle it that matters.
The few the proud the 27🏹

Offline bow101

  • Member
  • Posts: 2,235
Re: Lam bow
« Reply #5 on: January 15, 2014, 09:50:22 pm »
=================================================================
Don't think I'll use a power Lam because I already done the tapering and some floor tillering, have to get it bending more in the right places.  This one may come in slightly under weight,  I wanna hit about 45#


« Last Edit: January 23, 2014, 08:58:20 pm by bow101 »
Logged
"The privilege of a lifetime is being who you are."  Joseph Campbell

Offline bow101

  • Member
  • Posts: 2,235
Re: Update on (Lam bow)
« Reply #6 on: January 23, 2014, 08:58:34 pm »
 
At any rate I'm almost complete on this Maple MBM 2 lam bow.  1 1/2" @  fades 3/8" at the tips....
Its 66" NTN hit my target weight 47# @27" .    Now here is the dilema I over tillered the top limb, ended up with a hinge it was to late.  So I did a repair on the belly, not thinking should of done it on the Back and glued in some reflex seeing that it took some set after hinging. 
So today I sanded it and added a small piece of yew to the handle back.   It has 1" of positive tiller.  I did a mirror shot and the tiller looks really good and it looks ok on the tree.  No Twist at all and feels good in the hand.

I was thinking of maybe gluing on a proper lam chunk to the back where it hinged and scrape off the ugly part I glued on the belly.  The hinge is about 8" back from the nock.   Have 12 hours of work into it...
I will shoot it in tomorrow and see what it's like then.............   :-\

 
Logged
"The privilege of a lifetime is being who you are."  Joseph Campbell

Offline adb

  • Member
  • Posts: 5,339
Re: Update on (Lam bow)
« Reply #7 on: January 24, 2014, 09:50:22 am »
A hinge is a mistake in tillering. You've made a mistake... learn from it, and work hard to not repeat it. A bow with a severe hinge belongs on the junk pile, and the next one you make without a hinge does not!  ;)
Logged
Pages: [1]
« previous next »