« previous next »
Pages: [1] 2

Author Topic: bending boards?  (Read 3632 times)

0 Members and 1 Guest are viewing this topic.

Offline BowSlayer

  • Member
  • Posts: 644
bending boards?
« on: September 28, 2013, 07:39:23 am »
hey everyone. i have a board of oak. the limbs taper from 1 1/4" @ the fades to 3/4" @ the tips. they are 10mm thick. i wan't to bend in some working curves into the end of the bow. have any off you done this on a board before? would you say dry heat or steaming is better? any advice and tips would be much appreciated. thanks :laugh:
Logged
London, England.

45#@28"

Offline PEARL DRUMS

  • Member
  • Posts: 14,079
  • }}}--CK-->
Re: bending boards?
« Reply #1 on: September 28, 2013, 08:40:52 am »
Dry heat and be ready for a crack, leave material to remove on the thickness. Id wipe a dab of veggy oil on it, helps slow down moisture loss and keeps it from scorching the wood. It will sand right off.
Logged
Only when the last tree has died and the last river has been poisoned and the last fish has been caught will we realize we cannot eat money.

Offline bushboy

  • Member
  • Posts: 2,256
Re: bending boards?
« Reply #2 on: September 28, 2013, 09:22:18 am »
And I've been using this method lately with good sucess.wet down a cotton rag,heat gun it (don't over do it) ,flip the foil for a peek that there's good steaming action,then clamp it down,let it cool,remove foil and cloth and heat the tip so they are hot .I wouldn't try such a extreme cuvre like this with oak with this method.this is elm and it bends like butter!
Logged
Some like motorboats,I like kayaks,some like guns,I like bows,but not the wheelie type.

Offline BowSlayer

  • Member
  • Posts: 644
Re: bending boards?
« Reply #3 on: September 28, 2013, 11:17:58 am »
how thick is that limb? looks like a good methord. ill need to make a form though. could i do this over a pan full of water on the stove covered with tin foil? i ask because.. i don't have a heat gun  :-\ thanks
Logged
London, England.

45#@28"

Offline bushboy

  • Member
  • Posts: 2,256
Re: bending boards?
« Reply #4 on: September 28, 2013, 11:36:07 am »
The limb is bout 13.5mm(9/16").you could do it with steam,but you would have to get it clamped up very quickly!!!!! How were you planning on flipping the tips?torch,stove top?
Logged
Some like motorboats,I like kayaks,some like guns,I like bows,but not the wheelie type.

Offline BowSlayer

  • Member
  • Posts: 644
Re: bending boards?
« Reply #5 on: September 28, 2013, 11:50:22 am »
im going to make a form like the one you have there. but use steam to heat the wood. if i do it this way do i still need to add oil?
Logged
London, England.

45#@28"

Offline bushboy

  • Member
  • Posts: 2,256
Re: bending boards?
« Reply #6 on: September 28, 2013, 11:59:16 am »
Oil 4 dry heat I would think.
Logged
Some like motorboats,I like kayaks,some like guns,I like bows,but not the wheelie type.

Offline BowSlayer

  • Member
  • Posts: 644
Re: bending boards?
« Reply #7 on: September 28, 2013, 06:34:09 pm »
cool thanks. has anyone else tried bending board bows before?
Logged
London, England.

45#@28"

Offline dbb

  • Member
  • Posts: 745
Re: bending boards?
« Reply #8 on: September 28, 2013, 06:47:08 pm »
Yes,i and many more have.
I strongly suggest you set it all up beforehand and do a "dry" genrep so you have it all ready.
Makes it all easier that way.
Logged
It's better to ask and look like a fool than not to ask and remain one...

Offline BowSlayer

  • Member
  • Posts: 644
Re: bending boards?
« Reply #9 on: September 28, 2013, 07:00:25 pm »
will do, thanks
Logged
London, England.

45#@28"

Offline bushboy

  • Member
  • Posts: 2,256
Re: bending boards?
« Reply #10 on: September 29, 2013, 02:32:05 am »
Good catch jezze ,this was actually a piece of spaghetti !lol!
Logged
Some like motorboats,I like kayaks,some like guns,I like bows,but not the wheelie type.

Offline Cameroo

  • Member
  • Posts: 1,579
    • Cam's Stuff
Re: bending boards?
« Reply #11 on: September 29, 2013, 06:47:03 pm »
Bushboy, can I ask why you steam-heat with the towel, then allow it to cool, and then heat it directly with dry heat again? 
I've seen both methods used, but not together like that.
Logged

Offline bushboy

  • Member
  • Posts: 2,256
Re: bending boards?
« Reply #12 on: September 29, 2013, 07:01:40 pm »
Cam ,I heat treated only the recurve to lock it in.if it were a working part of the limb I'd be more concerned.
Logged
Some like motorboats,I like kayaks,some like guns,I like bows,but not the wheelie type.

Offline BowSlayer

  • Member
  • Posts: 644
Re: bending boards?
« Reply #13 on: September 30, 2013, 08:40:13 am »
i have a question, before i do any reflexing of the tips do i need to tiller with a longstring first?
Logged
London, England.

45#@28"

Offline BowSlayer

  • Member
  • Posts: 644
Re: bending boards?
« Reply #14 on: October 02, 2013, 09:43:12 am »
here is my first atempt at bending the board. steamed it for an hour. i do have one question how long do i keep it on the form? thanks.

 
Logged
London, England.

45#@28"
Pages: [1] 2
« previous next »