« previous next »
Pages: [1]

Author Topic: Need help with backing!  (Read 1212 times)

0 Members and 2 Guests are viewing this topic.

Offline crwjr

  • Member
  • Posts: 90
Need help with backing!
« on: April 02, 2013, 10:34:20 am »
I need some help on how to back a board bow, or any bow for that matter. I'm thinking of making a red oak with a hickory back for my next bow! Do I glue the two boards together or do I need to rip the backing board down? And if so what thickness? Thanks for the help everyone!
« Last Edit: April 02, 2013, 10:40:43 am by crwjr »
Logged
Pick a spot
Aim small miss small

Offline bushboy

  • Member
  • Posts: 2,256
Re: Need help with backing!
« Reply #1 on: April 02, 2013, 11:50:56 am »
Rip your backing strip to 3/16" ,then hand sand it to bout1/8".
Logged
Some like motorboats,I like kayaks,some like guns,I like bows,but not the wheelie type.

Offline bubby

  • Member
  • Posts: 11,054
Re: Need help with backing!
« Reply #2 on: April 02, 2013, 02:50:35 pm »
it's actually easyer to glue it up and then rip it as there I more wood and its a little safer with a tablesaw that way, bub
Logged
failure is an option, everyone fails, it's how you handle it that matters.
The few the proud the 27🏹

Offline Slackbunny

  • Member
  • Posts: 866
Re: Need help with backing!
« Reply #3 on: April 02, 2013, 03:14:07 pm »
Quote from: bubby on April 02, 2013, 02:50:35 pm
it's actually easyer to glue it up and then rip it as there I more wood and its a little safer with a tablesaw that way, bub

+1.

 I can vouch for that one from experience. It makes it easier and safer. The only cuts I make before the glue up are just to get the pieces down to slightly oversized. Then I glued them up and work with a nice solid piece from there on out.

 
Logged

Offline bushboy

  • Member
  • Posts: 2,256
Re: Need help with backing!
« Reply #4 on: April 02, 2013, 04:03:23 pm »
I cut them in strips in order to glue in some reflex at time of laminations.I agree on the safety factor of the preglue method,makes sense to me.
Logged
Some like motorboats,I like kayaks,some like guns,I like bows,but not the wheelie type.

Offline crwjr

  • Member
  • Posts: 90
Re: Need help with backing!
« Reply #5 on: April 02, 2013, 07:27:03 pm »
Thanks for all the advice. What about a log stave not a board, how would you back one of these? Flatten out the back?
Logged
Pick a spot
Aim small miss small

Offline lesken2011

  • Member
  • Posts: 2,063
  • Kenny
Re: Need help with backing!
« Reply #6 on: April 02, 2013, 07:33:27 pm »
A stave where you have chased a single ring generally does not require a backing, but something like rawhide, linen, or silk will mold itself to the back for extra protection.
Logged
For by grace you have been saved through faith, and that not of yourselves; it is the gift of God, not of works, lest anyone should boast.

Ephesians 2:8-9

Kenny from Mississippi, USA

Offline Pat B

  • Administrator
  • Member
  • Posts: 37,633
Re: Need help with backing!
« Reply #7 on: April 02, 2013, 08:46:22 pm »
If a strave has a good back I would never consider backing it with a rigid backing. You won't get a better back than the original.
Logged
Make the most of all that comes and the least of all that goes!    Pat Brennan  Brevard, NC

Offline Eric Krewson

  • Member
  • Posts: 5,432
Re: Need help with backing!
« Reply #8 on: April 02, 2013, 08:53:30 pm »
I have  backed a bunch of oak boards for folk with hickory, some hickory backed hickory, backed about 50 osage staves with bamboo, questionable wood, very tight rings and more early wood than late wood, all made great bows with a strip of added bamboo.

If you have a questionable stave you want to salvage, flatten the back and back it. Like Pat said, a good stave is better off staying a stave.
Logged
Pages: [1]
« previous next »