« previous next »
Pages: [1] 2

Author Topic: a shaft press for tricky shoots  (Read 3068 times)

0 Members and 1 Guest are viewing this topic.

Offline richardzane

  • Member
  • Posts: 500
  • active Wyandot tribal member
    • richardzanesmith.wordpress.com
a shaft press for tricky shoots
« on: March 26, 2013, 08:42:54 pm »
since i've been using alot of wild rose and other wavy shoots that can be a bear to straighten,
I made this adjustable shaft press from scrap wood and have been enjoying it..in fact i maybe addicted now.
the press sits on my work table with an anchored hook behind it to make it a one handed operation.
it takes a little getting used to..its easy to dent a shaft with too much force, so i put a piece of leather around the handle for a bit of cushion.
which can be slid away if I'm working a hard wood.
I've never seen anybody make one of these , but i'm sure its been done. :)
Logged
when i'm working on things my ancestors worked, singing the songs my ancestors sang, dancing the same dances, speaking the same language, only then  I feel connected to the land, THIS land, where my ancestors walked for thousands of years...

Offline CherokeeKC

  • Member
  • Posts: 574
  • PM108323
Re: a shaft press for tricky shoots
« Reply #1 on: March 26, 2013, 08:45:13 pm »
Interesting!  I like it.  I have some wild rose shoots also so might have to try one of these out.
Logged
Aim Small...Hit Small

Offline Thesquirrelslinger

  • Member
  • Posts: 1,245
Re: a shaft press for tricky shoots
« Reply #2 on: March 26, 2013, 09:33:57 pm »
Holy crud that is nice... How did you make it?

Logged
"Insanity is doing the same thing over and over again and expecting different results"

Offline TRACY

  • Member
  • Posts: 4,523
Re: a shaft press for tricky shoots
« Reply #3 on: March 26, 2013, 10:41:40 pm »
Ingenious tool for straightening. I've seen other devices but like this one. That rose shaft looks really good!

Tracy
Logged
It is what it is - make the most of it!    PN500956

Offline Don

  • Member
  • Posts: 331
Re: a shaft press for tricky shoots
« Reply #4 on: March 26, 2013, 11:29:47 pm »
Great idea. I like it.
Logged

Offline Pat B

  • Administrator
  • Member
  • Posts: 37,637
Re: a shaft press for tricky shoots
« Reply #5 on: March 26, 2013, 11:49:07 pm »
Necessity is the mother of invention!  8) Cool tool. It would work great on some of those kinks that are hard to remove.
Logged
Make the most of all that comes and the least of all that goes!    Pat Brennan  Brevard, NC

Offline Pappy

  • Global Moderator
  • Member
  • Posts: 32,207
  • if you have to ask you wouldn't understand ,Tenn.
Re: a shaft press for tricky shoots
« Reply #6 on: March 27, 2013, 08:04:11 am »
Very cool,I may try and make one of those.Thanks.
   Pappy
Logged
Clarksville,Tennessee
TwinOaks Bowhunters
Life is Good

Offline Scowler

  • Member
  • Posts: 611
Re: a shaft press for tricky shoots
« Reply #7 on: March 27, 2013, 08:40:16 am »
Very inventive.  Glad its working for you.
Logged

Offline richardzane

  • Member
  • Posts: 500
  • active Wyandot tribal member
    • richardzanesmith.wordpress.com
Re: a shaft press for tricky shoots
« Reply #8 on: March 27, 2013, 11:13:54 am »
thanks for the comments!
I was getting frustrated with some of the "kinks" as Pat B called em,
it just seemed the arrow wrench could take out drift and sway but shoots with risers like    ====^=====^====    were still a problem.

Tracy,  the shoot there on the press is hazel and didn't have too may kinks to start with.
Logged
when i'm working on things my ancestors worked, singing the songs my ancestors sang, dancing the same dances, speaking the same language, only then  I feel connected to the land, THIS land, where my ancestors walked for thousands of years...

Offline richardzane

  • Member
  • Posts: 500
  • active Wyandot tribal member
    • richardzanesmith.wordpress.com
Re: a shaft press for tricky shoots
« Reply #9 on: March 27, 2013, 11:31:24 am »
squirrelslinger,
its pretty simple really... do a few sketches,  look in the workshop and see whats laying around and have at it.

I'm sure it could be made a lot easier than this...  you could use a door hinge or a heavy eyebolt as the "hinge" with a thick dowel or broomstick handle passing through it.
My handle is just a  1 1/4" dowel with a 3/8" dowel passing through it.
the two rounded walnut "hinge"pieces are screwed and glued from underneath with deck screws.
the blocks (on the press part) are simply scraps of walnut clamped together and drilled where the two pieces meet. I made mine 1/2" and the other side  11/32"
the 1/2" for preliminary straightening on partially seasoned shoots like these 65 or so wild rose in the pic.
Logged
when i'm working on things my ancestors worked, singing the songs my ancestors sang, dancing the same dances, speaking the same language, only then  I feel connected to the land, THIS land, where my ancestors walked for thousands of years...

Offline Trapper Rob

  • Member
  • Posts: 3,719
Re: a shaft press for tricky shoots
« Reply #10 on: March 27, 2013, 01:48:45 pm »
I like that I have to make me one.
Rob
Logged

Offline ncpat

  • Member
  • Posts: 98
Re: a shaft press for tricky shoots
« Reply #11 on: March 27, 2013, 07:59:36 pm »
Great idea! Looks like it would work well.
Logged
Remember the heroes of Flight 93.

Offline Thesquirrelslinger

  • Member
  • Posts: 1,245
Re: a shaft press for tricky shoots
« Reply #12 on: March 27, 2013, 08:13:58 pm »
OK... where are some wild rose shoots? I want to make some arrow shafts:)
Logged
"Insanity is doing the same thing over and over again and expecting different results"

Offline Slackbunny

  • Member
  • Posts: 866
Re: a shaft press for tricky shoots
« Reply #13 on: March 27, 2013, 09:07:20 pm »
Somebody call the cops! I'm totally stealing that idea.
Logged

Offline Frawg

  • Member
  • Posts: 282
  • Mayan Apocalypse Survivor
    • N/A
Re: a shaft press for tricky shoots
« Reply #14 on: March 27, 2013, 10:54:14 pm »
Very nice, I like the looks of that.
Matt
Logged
Matt Bradley

Glade Valley, NC
Pages: [1] 2
« previous next »