« previous next »
Pages: [1]

Author Topic: knot ?  (Read 1814 times)

0 Members and 1 Guest are viewing this topic.

Offline bubby

  • Member
  • Posts: 11,054
knot ?
« on: March 22, 2013, 07:08:24 pm »
what kind of epoxies do you guys use when filling knots, got some on a bow i'm working on, Bub
Logged
failure is an option, everyone fails, it's how you handle it that matters.
The few the proud the 27🏹

Offline Del the cat

  • Member
  • Posts: 8,322
    • Derek Hutchison Native Wood Self Bows
Re: knot ?
« Reply #1 on: March 22, 2013, 07:19:48 pm »
I use a '151' a 10 minute epoxy mixed with saw dust, use plenty of dust until the mix feels too dry. As it's tamped into the hole it seems to get wetter some how. Anything bigger than about 1/8" I'll stick in a peg using the same epoxy.
Del
(Don't use Araldite 'rapid' it's cr4p)
Logged
Health warning, these posts may contain traces of nut.

Offline bow101

  • Member
  • Posts: 2,235
Re: knot ?
« Reply #2 on: March 22, 2013, 07:26:38 pm »
We were using clear epoxy [24 hr.] stuff seems to be stronger, that's my 2 cents.
Logged
"The privilege of a lifetime is being who you are."  Joseph Campbell

Offline bubby

  • Member
  • Posts: 11,054
Re: knot ?
« Reply #3 on: March 22, 2013, 08:05:02 pm »
thank's
Logged
failure is an option, everyone fails, it's how you handle it that matters.
The few the proud the 27🏹

Offline PEARL DRUMS

  • Member
  • Posts: 14,079
  • }}}--CK-->
Re: knot ?
« Reply #4 on: March 22, 2013, 08:19:16 pm »
Loctite brand super glue for any and all fillin's I do. I will fill some big ol' knots with it.......you might just find that out bub!
Logged
Only when the last tree has died and the last river has been poisoned and the last fish has been caught will we realize we cannot eat money.

Offline bubby

  • Member
  • Posts: 11,054
Re: knot ?
« Reply #5 on: March 22, 2013, 08:30:48 pm »
sounds good Chris, ya got me thinking now
Logged
failure is an option, everyone fails, it's how you handle it that matters.
The few the proud the 27🏹

Offline lesken2011

  • Member
  • Posts: 2,063
  • Kenny
Re: knot ?
« Reply #6 on: March 22, 2013, 09:51:39 pm »
Do a knot fill-a-long, Bub!! :P
Logged
For by grace you have been saved through faith, and that not of yourselves; it is the gift of God, not of works, lest anyone should boast.

Ephesians 2:8-9

Kenny from Mississippi, USA

Offline Pat B

  • Administrator
  • Member
  • Posts: 37,633
Re: knot ?
« Reply #7 on: March 22, 2013, 11:52:56 pm »
I use super glue also. No specific variety just whatever I pick up. I usually put super glue on every knot and pin on the back of a bow I'm building and sometimes the belly side after tillering. If the knots are hollow I will start with a little glue then sprinkle fine saw dust and let it set then I do it again and again if necessary until the filled knot is flush with the limb surface. I found if I try to fill a knot at one time I sometimes got voids that the glue didn't penetrate. By doing it in layers I'm assured a good, solid repair.
Logged
Make the most of all that comes and the least of all that goes!    Pat Brennan  Brevard, NC

Offline Del the cat

  • Member
  • Posts: 8,322
    • Derek Hutchison Native Wood Self Bows
Re: knot ?
« Reply #8 on: March 23, 2013, 05:11:07 am »
This is a knot fillin' job :o  (90# ELB)
Excavated, filled with sawdust/epoxy, then:-
Drilled for a plug, filed flat.
Drilled for a plug, filed flat.
Drilled for a plug, filed flat.
Drilled for a plug, filed flat, ok the last plug was a tad smaller than the other 3/8" ones  :o
Don't reckon there's enough superglue in the UK to fill that bad boy, it was sooo deep I struck oil >:D
The important thing about it is that there's good sound continuous sapwood over the area.
Del
Logged
Health warning, these posts may contain traces of nut.
Pages: [1]
« previous next »