« previous next »
Pages: [1]

Author Topic: Anybody ever have a scrapper scrap unevenly across ring transitions?  (Read 2665 times)

0 Members and 2 Guests are viewing this topic.

Offline toomanyknots

  • Member
  • Posts: 3,132
Anybody ever have a scrapper scrap unevenly across ring transitions?
« on: January 11, 2013, 01:12:22 pm »
What I mean is, take the gradual ring transition down the belly of a limb on a typical bow, where the rings feather out towards the nock. I have been having a problem where my scraper will sort of jump rings, and this will make a bump where the next ring starts. It is also pretty square, and not natural looking, it stands out pretty bad. Anybody know what I am talking about? I am using a straight scraper, it is probably not super sharp, but it ain't dull or nothing.
Logged
"The way of heaven is like the bending of a bow-
 the upper part is pressed down,
 the lower part is raised up,
 the part that has too much is reduced,
 the part that has too little is increased."

- Tao Te Ching, 77, A new translation by Victor H. Mair

Offline Gordon

  • Member
  • Posts: 3,299
Re: Anybody ever have a scrapper scrap unevenly across ring transitions?
« Reply #1 on: January 11, 2013, 01:13:52 pm »
Are you working with osage?
Logged
Gordon

Offline ionicmuffin

  • Member
  • Posts: 1,787
Re: Anybody ever have a scrapper scrap unevenly across ring transitions?
« Reply #2 on: January 11, 2013, 01:22:02 pm »
i have a similar problem with mine! i think its very dull though. it mostly happens either at rings, or at knots or other hard sections.
Logged
Amo innectis arcus- I love crafting bows (latin)

Offline Pat B

  • Administrator
  • Member
  • Posts: 37,609
Re: Anybody ever have a scrapper scrap unevenly across ring transitions?
« Reply #3 on: January 11, 2013, 01:26:50 pm »
That is the softer early ring being scraped more than the harder heartwood. If you don't get too much of a dip you can even it up using a sanding block when you get to final sanding. It is a pretty common problem when using woods like osager, locust, mulberry, etc.
Logged
Make the most of all that comes and the least of all that goes!    Pat Brennan  Brevard, NC

Offline MWirwicki

  • Member
  • Posts: 2,234
  • The wood speaks to you; Listen with your eyes. GSD
Re: Anybody ever have a scrapper scrap unevenly across ring transitions?
« Reply #4 on: January 11, 2013, 01:28:43 pm »
Like Pat said.  I use a finer file to blend the two surfaces.  Then only finish it up with sandpaper.
Logged
Matt Wirwicki
Owosso, MI

Offline toomanyknots

  • Member
  • Posts: 3,132
Re: Anybody ever have a scrapper scrap unevenly across ring transitions?
« Reply #5 on: January 11, 2013, 01:50:21 pm »
Quote from: Gordon on January 11, 2013, 01:13:52 pm
Are you working with osage?

 ;D, yup.
Logged
"The way of heaven is like the bending of a bow-
 the upper part is pressed down,
 the lower part is raised up,
 the part that has too much is reduced,
 the part that has too little is increased."

- Tao Te Ching, 77, A new translation by Victor H. Mair

Offline toomanyknots

  • Member
  • Posts: 3,132
Re: Anybody ever have a scrapper scrap unevenly across ring transitions?
« Reply #6 on: January 11, 2013, 01:53:30 pm »
Quote from: Pat B on January 11, 2013, 01:26:50 pm
That is the softer early ring being scraped more than the harder heartwood. If you don't get too much of a dip you can even it up using a sanding block when you get to final sanding. It is a pretty common problem when using woods like osager, locust, mulberry, etc.

Quote from: MWirwicki on January 11, 2013, 01:28:43 pm
Like Pat said.  I use a finer file to blend the two surfaces.  Then only finish it up with sandpaper.

Alrighty, sounds like a plan. Thank ya guys. Ya, it was on an osage bow I just finished it up. I thought I had sanded em down, than after finish sanding to 1000 grit, burnishing, and waxing, then I noticed that I still had some pretty big square indentations. Which thanks to the finish, are now painfully obvious,  ;D.
Logged
"The way of heaven is like the bending of a bow-
 the upper part is pressed down,
 the lower part is raised up,
 the part that has too much is reduced,
 the part that has too little is increased."

- Tao Te Ching, 77, A new translation by Victor H. Mair

mikekeswick

  • Guest
Re: Anybody ever have a scrapper scrap unevenly across ring transitions?
« Reply #7 on: January 11, 2013, 02:00:26 pm »
The problem gets worse the duller your scraper gets. The less sharp the more pressure you have to use to 'force' it to bite. They should always be sharp enough to 'wipe' shavings off with one hand. ;)
The easy way to stop it happening is only ever use a super sharp scraper.
Then if this problems starts to form then flatten with files.
Logged

Offline SLIMBOB

  • Member
  • Posts: 3,759
  • Deplorable Slim
Re: Anybody ever have a scrapper scrap unevenly across ring transitions?
« Reply #8 on: January 11, 2013, 03:39:01 pm »
The key is not to let it get to deep.  As one appears, I use the sanding block as Pat said, and smooth it out completely.  Then back to the scraper, then repeat the sanding block and so on.  The thick ringed stuff is more of a problem as there is usually more early wood.  Sharper tools will minimize it.
Logged
Liberty, In God We Trust, E Pluribus Unum.  Distinctly American Values.

Offline adb

  • Member
  • Posts: 5,339
Re: Anybody ever have a scrapper scrap unevenly across ring transitions?
« Reply #9 on: January 11, 2013, 04:56:42 pm »
If I'm tillering osage, this happens. To prevent it, I alternate between scraper and rasp. The rasp will knock off the harder high spots, and then you can work with the scraper again. Keep the burr on your scraper fresh and it won't be as bad.
Logged

Offline dwardo

  • Member
  • Posts: 1,456
Re: Anybody ever have a scrapper scrap unevenly across ring transitions?
« Reply #10 on: January 11, 2013, 05:15:27 pm »
Having two cab scrapers helps.
Sharpen both and when you start to question one, try the other and see if its you being too tired or the scraper blunting.
Logged

Offline Gordon

  • Member
  • Posts: 3,299
Re: Anybody ever have a scrapper scrap unevenly across ring transitions?
« Reply #11 on: January 11, 2013, 05:17:10 pm »
It's all been said already - sharp scraper followed by a sanding block.
Logged
Gordon
Pages: [1]
« previous next »