« previous next »
Pages: [1]

Author Topic: Second Bow - Tillering Help  (Read 1400 times)

0 Members and 1 Guest are viewing this topic.

Offline Socal

  • Member
  • Posts: 2
Second Bow - Tillering Help
« on: September 13, 2012, 04:37:58 pm »
Hey guys!  Brand new to the forum and bow making, and I'm working on my second bow now, a 63" red oak board with a maple riser based off the Meare Heath design.  I'm shooting for 35# at 26", got it to were I can string it with about a 3" brace height, and I was wondering if anyone could give me a second opinion on how the tillering's going.  I've heard some things about red oak, so I want to make sure I'm doing it right.



Here's it pulled 10":


I think there's a hinge on the left limb, but confirmation never hurt.  Any feedback would be great, thanks guys!
Logged

Offline Carson (CMB)

  • Member
  • Posts: 2,319
Re: Second Bow - Tillering Help
« Reply #1 on: September 13, 2012, 06:13:24 pm »
It doesn't look too hingey to me.  I like to get a normal brace as soon as possible to confirm the balance of the limbs. Looks like you could put a shorter string on there at this point.  Looks like mid-limb is a little stiff yet on both limbs.
Logged
"The bow is the old first lyre,
the mono chord, the initial rune of fine art
The humanities grew out from archery as a flower from a seed
No sooner did the soft, sweet note of the bow-string charm the ear of genius than music was born, and from music came poetry and painting and..." Maurice Thompso

Offline PEARL DRUMS

  • Member
  • Posts: 14,079
  • }}}--CK-->
Re: Second Bow - Tillering Help
« Reply #2 on: September 13, 2012, 06:23:00 pm »
Yup. Full brace it and see what it says. Start at about 5 1/4".
Logged
Only when the last tree has died and the last river has been poisoned and the last fish has been caught will we realize we cannot eat money.

Offline Socal

  • Member
  • Posts: 2
Re: Second Bow - Tillering Help
« Reply #3 on: September 13, 2012, 06:24:59 pm »
Alright cool, thanks guys.
Logged

Offline bubby

  • Member
  • Posts: 11,054
Re: Second Bow - Tillering Help
« Reply #4 on: September 13, 2012, 06:39:08 pm »
after you get full brace, make a tillering gizzmo, top of the how to page, will help alot tillering, Bub
Logged
failure is an option, everyone fails, it's how you handle it that matters.
The few the proud the 27🏹

mikekeswick

  • Guest
Re: Second Bow - Tillering Help
« Reply #5 on: September 14, 2012, 04:24:01 am »
I wouldn't be bracing it higher yet.
A higher brace height = more stress = more string follow.
The right limb is bending a little too much just to the handle side of mid limb with the tipwards side being stiff.
The left limb is the same but not quite as pronounced.
Get the outer limbs working a little more.
As your limbs are parallel width for a long way you will have a taper in the thickness.
As the wood thins out towards the tips the bend should be increasing - elliptical tiller.
Logged

Offline Pappy

  • Global Moderator
  • Member
  • Posts: 32,137
  • if you have to ask you wouldn't understand ,Tenn.
Re: Second Bow - Tillering Help
« Reply #6 on: September 14, 2012, 07:21:52 am »
Agree with Mike. A few scrapes on the right mid to outer limb and about twice as many on the left ,same area and then I would go to full brace. Looking very good so far. :)
   Pappy
Logged
Clarksville,Tennessee
TwinOaks Bowhunters
Life is Good
Pages: [1]
« previous next »