« previous next »
Pages: [1]

Author Topic: Recurve Jig Question  (Read 4001 times)

0 Members and 1 Guest are viewing this topic.

Offline JonW

  • Member
  • Posts: 1,906
Recurve Jig Question
« on: August 18, 2011, 08:45:46 pm »
I started to lay out a pattern for a recurve jig and I can't decide on the diameter of the circle I want to use. What do some of you guys use?

Jon W.
Logged

Offline bubby

  • Member
  • Posts: 11,054
Re: Recurve Jig Question
« Reply #1 on: August 18, 2011, 09:25:19 pm »
I used a 5 gal bucket for one, Bub
Logged
failure is an option, everyone fails, it's how you handle it that matters.
The few the proud the 27🏹

Offline Pat B

  • Administrator
  • Member
  • Posts: 37,893
Re: Recurve Jig Question
« Reply #2 on: August 18, 2011, 10:00:59 pm »
Probably 6" or more radius. 8" to 10" radius might be better for your first.
Logged
Make the most of all that comes and the least of all that goes!    Pat Brennan  Brevard, NC

Offline JonW

  • Member
  • Posts: 1,906
Re: Recurve Jig Question
« Reply #3 on: August 18, 2011, 10:30:19 pm »
Wouldn't 6" radius be like a pop can? I was thinking about something like a five gallon bucket but it seemed big when you look at the circle. Wood is pretty cheap though and I can try some different sizes.
Logged

Offline Catnapper

  • Member
  • Posts: 73
Re: Recurve Jig Question
« Reply #4 on: August 18, 2011, 11:57:04 pm »
Radius is measured from the center of the circle to the outside so a popcan would be like a 1.5" radius. A 5 gallon bucket would be about 6" radius......i have also been wondering what size of circle to use for a recurve so im glad  u posted this question.  :)
Logged
Gillette, Wyoming

mikekeswick

  • Guest
Re: Recurve Jig Question
« Reply #5 on: August 19, 2011, 06:38:16 am »
The smaller the radius the more energy stored by the limb.. :)all things being equal! The smaller the radius the harder the wood is to bend! >:D
Logged

Offline Prarie Bowyer

  • Member
  • Posts: 1,599
Re: Recurve Jig Question
« Reply #6 on: August 21, 2011, 01:38:46 am »
The larger the radius the less likley to snap the wood.  5 gal bucket is a good starting place.  I should have used that. 
Logged

Offline Pat B

  • Administrator
  • Member
  • Posts: 37,893
Re: Recurve Jig Question
« Reply #7 on: August 21, 2011, 12:25:32 pm »
I used the wrong termalology I guess. A 6" diameter or bigger circle would be a good place to start.
Logged
Make the most of all that comes and the least of all that goes!    Pat Brennan  Brevard, NC

Offline makenzie71

  • Member
  • Posts: 572
  • I can robin hood an arrow if I hit it just right.
Re: Recurve Jig Question
« Reply #8 on: August 21, 2011, 01:57:40 pm »
I'm doing my first laminate recurve right now...I don't have a lot of hope for it but oh well.  I'm using a piece of 18" steel pipe as a form, flipping the last 12" of the limbs.
Logged
Goodbye, friends. I never thought I'd die like this. But I always really hoped. ~ Fry

Offline Prarie Bowyer

  • Member
  • Posts: 1,599
Re: Recurve Jig Question
« Reply #9 on: August 22, 2011, 09:56:07 pm »
Mine broke.  So much time and effort it's hardly worth it.  Maybee wood species makes a difference but I tried to use the 4estTrecker method and I wound up piking the bow.  Both sides cracked split and simply broke.  I've seen some realy big recurve tip overlays that were glued on .  I may try that method next.

My radius was the top of a 5 gal bucket for an 11" section that was pretapered.
Logged
Pages: [1]
« previous next »