Author Topic: set question (Read 2856 times)

Frode · « **on:** December 24, 2009, 03:29:08 pm »

Hi all,
I see that my first three bows all have between 1" and 2" of set (string follow?) per side. All are board bows, two in maple with lesser amounts and one in red oak with the most amount of set. I've exercised all these boards after each removal of material and short drawn them many times leading up to full draw.
I notice many of the stave bows here seem very straight unstrung. Does the difference have something to do with my novice tillering, or is there something about boards versus staves that explains it? All three seem to shoot fine, and the amount of set doesn't seem to increase or decrease by any visible amount. Just curious.
Thanks,
Frode

[attachment deleted by admin]

Pat B · « **Reply #1 on:** December 24, 2009, 03:47:44 pm »

Frode, As George says..."set happens"!!!

One to 2 inches of set is not bad and is quite common with most wood bows.The reason some of the stave bows don't seem to have any set is because they have reflex added while straightening and some have tempered bellies as well. This can be done with board bows also.
Any wood bow is going to have some set just because they are natural materials and the compression stresses of making a bow cause the belly cells to collapse or become malformed somewhat. If you get 3" to 4" or more of set then you might be causing it while building the bow but 2" isn't bad at all and will make for a sweeter shooting bow.

cracker · « **Reply #2 on:** December 24, 2009, 03:57:51 pm »

I second what Pat said.Ron

sailordad · « **Reply #3 on:** December 24, 2009, 04:03:05 pm »

i'll 3rd what at said

as george is known to say, "set happens"

M-P · « **Reply #4 on:** December 24, 2009, 05:29:58 pm »

Actually what we're talking about here is "string follow" In your bows it's the same as 'set", since you started with a straight stave/ board. All bows take some set and as everyone else pointed out 1-2" shows care in tillering and makes for a sweet bow. If you want a bow with no string follow, just steam two inches of reflex into your stave before tillering ( or induce reflex while heat treating, or ....). The bow will take some set , but wind up with near zero string follow. Ron

sulphur · « **Reply #5 on:** December 24, 2009, 06:03:50 pm »

the only way to lessen set or string follow is to start out with a reflexed stave. osage is great about resisting string follow, everything else gets so so results. heat in a little reflex (2-3") before you start to tiller and that should help.

Frode · « **Reply #6 on:** December 24, 2009, 06:27:17 pm »

Thank you, everyone, my education continues! Good to know it's not a problem, and even beneficial!

Frode

daryush · « **Reply #7 on:** December 24, 2009, 08:12:00 pm »

This is going to sound silly, but what's the difference between set and string follow?

sailordad · « **Reply #8 on:** December 24, 2009, 09:40:47 pm »

string follow-the amount the bows stays bent for a short time after it is unbraced

set-the amount the wood stays bentafter the bow is finished

so if you start with a piece of wood that i perfectly straight and make a bow.when the bow id finished and the wood is
no longer flat but is bent towards the belly,lets say one inch,that would be set.now lets say you string the bow and shoot it some and unbrace it
and the limbs are bent towards the belly,lets say 2" from flat,and after short time of being unbraced it settles back to 1".
then you have 1" of set and 1" of follow.
atleast thats the best i can explain it

shamus · « **Reply #9 on:** December 25, 2009, 10:43:35 am »

2" or less of string follow is perfectly normal for a properly tillered, straight staved selfbow. It means you're doing it right. Don't sweat it.

El Destructo · « **Reply #10 on:** December 25, 2009, 11:33:00 am »

Tim....I don't think it could be explained any simpler than That....

Primitive Archer