« previous next »
Pages: [1]

Author Topic: osage bowstaves  (Read 3511 times)

0 Members and 1 Guest are viewing this topic.

Offline luke the drifter

  • Member
  • Posts: 171
osage bowstaves
« on: November 25, 2009, 01:01:45 pm »
bear with folks this the first time i have done this.  look these pictures over and offer advice if any about how to start and to solve potential problems












Logged

Offline George Tsoukalas

  • Member
  • Posts: 9,425
    • Traditional and Primitive Archers
Re: osage bowstaves
« Reply #1 on: November 25, 2009, 01:36:36 pm »
Luke, go to the first good sized ring you see.  I don't see anything unusual about them.  Jawge
Logged
Set Happens!
If you ain't breakin' you ain't makin!

Offline knap_123

  • Member
  • Posts: 572
Re: osage bowstaves
« Reply #2 on: November 25, 2009, 02:24:41 pm »
yep, yep,i see the problem here, thats not my table there sitting on!   ;D  good looking wood my friend, start chasing a ring
Logged

Offline Dean Marlow

  • Member
  • Posts: 531
Re: osage bowstaves
« Reply #3 on: November 25, 2009, 04:48:55 pm »
Looks like you get a real clean Osage stave there. Hard to find. Like evrybody else says. Find and chase the ring you want then draw your center line following the grain and you are on your way. Good luck  on that nice piece of wood. Dean
Logged

Offline luke the drifter

  • Member
  • Posts: 171
Re: osage bowstaves
« Reply #4 on: November 25, 2009, 11:04:30 pm »
i am kind of concerned about the fourth picture down.  there is a a hump there that i don't quite know how to handle.  my first inclination is that will tiller into a hinge, unless there is a way around that.  do i tiller around that hump or tiller it into the bend.  i appreciate any and all advice and responses.
Logged

Offline Pat B

  • Administrator
  • Member
  • Posts: 37,543
Re: osage bowstaves
« Reply #5 on: November 26, 2009, 12:00:26 am »
Basically, when tillered, the limbs will taper from fades to the tips in thickness and width. When you come to a knot you try to center it in the width of the limb and leave it proud from back to belly. If you can't center the knot in the limb, leave extra wood around the knot from side to side. Also, you want to follow the undulations of the back as you taper the limb thickness. Those "hoop-ti-dos"  are decieving and take concentration to tame.
Logged
Make the most of all that comes and the least of all that goes!    Pat Brennan  Brevard, NC

Offline shamus

  • Member
  • Posts: 332
Re: osage bowstaves
« Reply #6 on: November 26, 2009, 09:36:51 am »
looks like a nice failry straight and clean stave. Not sure about the earlywood/latewood ratios (pictures a bit blurrry).

This might help:

Evaluating Osage: http://analogperiphery.blogspot.com/2009/10/evaluating-osage.html

Tillering profiles : http://analogperiphery.blogspot.com/2009/04/tiller-profiles.html

Osage flatbow design: http://analogperiphery.blogspot.com/2008/05/osage-flat-bow-dimensions.html

Also, check out Geroge's site http://georgeandjoni.home.comcast.net/~georgeandjoni/ and Sam's site: http://www.geocities.com/salampsio/index.html

 Good stuff there.
Logged
Pages: [1]
« previous next »