« previous next »
Pages: [1]

Author Topic: How to make laminated tapers  (Read 8465 times)

0 Members and 1 Guest are viewing this topic.

Offline Mohammad Javad Shoaee

  • Member
  • Posts: 16
How to make laminated tapers
« on: November 02, 2009, 05:55:31 am »
Hello

Does anyone know how to make a a lamination taper with thickness sander?

Thank You
Logged

Offline El Destructo

  • Member
  • Posts: 8,078
  • Longhaired Crippled Hippie Biker And Proud Of It!!
    • Desert Sportz Primitive Archery
Re: How to make laminated tapers
« Reply #1 on: November 02, 2009, 07:03:01 am »
PM a dude named Islandpiper on this Board....He can probably help you out
Logged
As a species we're fundamentally insane. Put more than two of us in a room, we pick sides and start dreaming up ways to kill one another.Why do you think we invented politics and religion.
Think HEALTHCARE Is Expensive Now,Wait Till It's FREE
Do Or Do Not,There Is No TRY
2024...We Will Overcome

Offline Ryano

  • Member
  • Posts: 3,578
  • Ryan O'Sullivan, North Western Pennsylvania
Re: How to make laminated tapers
« Reply #2 on: November 08, 2009, 10:11:36 am »
make a tapered block for lamination to sit on and then run it through......
Logged
Its November, I'm gone hunt'in.......
Osage is still better.....

Offline adb

  • Member
  • Posts: 5,339
Re: How to make laminated tapers
« Reply #3 on: November 08, 2009, 11:04:55 am »
I think it would be very difficult with a thickness sander, but it's easy with a jointer.
Logged

Offline stiknstring

  • Member
  • Posts: 376
Re: How to make laminated tapers
« Reply #4 on: November 13, 2009, 08:25:41 pm »
Quite the opposite....when you start dealing with laminations in the .060 range tear out from jointers and planers is a big problem....with a thickness or drum sander like the performax it is a breeze.
Logged

Offline adb

  • Member
  • Posts: 5,339
Re: How to make laminated tapers
« Reply #5 on: November 13, 2009, 09:54:28 pm »
OK, can you show us?
Logged

Offline Justin Snyder

  • Administrator
  • Member
  • Posts: 13,794
Re: How to make laminated tapers
« Reply #6 on: November 13, 2009, 10:09:04 pm »
Quote from: stiknstring on November 13, 2009, 08:25:41 pm
Quite the opposite....when you start dealing with laminations in the .060 range tear out from jointers and planers is a big problem....with a thickness or drum sander like the performax it is a breeze.
Yes, I would love to trade my planer for a thickness sander when doing laminations.
Logged
Everything happens for a reason, sometimes the reason is you made a bad decision.


SW Utah

radius

  • Guest
Re: How to make laminated tapers
« Reply #7 on: November 14, 2009, 07:50:53 am »
Quote from: Justin Snyder on November 13, 2009, 10:09:04 pm
Quote from: stiknstring on November 13, 2009, 08:25:41 pm
Quite the opposite....when you start dealing with laminations in the .060 range tear out from jointers and planers is a big problem....with a thickness or drum sander like the performax it is a breeze.
Yes, I would love to trade my planer for a thickness sander when doing laminations.

why not have one of each?
Logged

Offline Justin Snyder

  • Administrator
  • Member
  • Posts: 13,794
Re: How to make laminated tapers
« Reply #8 on: November 14, 2009, 10:35:51 am »
$
Logged
Everything happens for a reason, sometimes the reason is you made a bad decision.


SW Utah

Offline stiknstring

  • Member
  • Posts: 376
Re: How to make laminated tapers
« Reply #9 on: November 14, 2009, 09:52:01 pm »
Truth money is an issue....head on over to the pirates of archery site and I am pretty sure you can see lots of lam grinders in various posts.  Can I show you???....no, I cannot afford one of those.  Can I listen to bowbuilders talk about grinding THIN (like 45 hundredths of an inch) laminations YOU BETCHA.  There is a good reason that I order from the guys who do it.

Weekend before last as I was grinding down some big ole bamboo for a BBI on my friends 80 inch belt sander he ground a eight or nine skinny ( ranging from .064 to .110) tapers and parallels on his performax for a couple kids bow projects I have in mind.  No tear out and baby but smooth and ready to glue.  That is testimony enough for me. They are pricy...I just found a used older model for 850....
« Last Edit: November 14, 2009, 10:11:11 pm by stiknstring »
Logged
Pages: [1]
« previous next »