« previous next »
Pages: [1]

Author Topic: Staining POC  (Read 3093 times)

0 Members and 1 Guest are viewing this topic.

Offline zeNBowyer

  • Member
  • Posts: 649
Staining POC
« on: October 05, 2009, 05:18:24 am »
I  have  been  trying to  stain  some POC  shafts  for  several weeks  now,  with  poor results, I tried sanding  off what  looks  like  a small coating of a  clear  coat  which  I   imagine  the manufacturers put  on  to  weatherize  the  shafts during  storage  and  shipment,  also  tried  using a  stain  prep  to  help  the  wood  absorb  the  stain- still  with poor results,
yet  the web  searches  I get  say POC takes  stain  well, what the  deal  here???
Logged
"There's  something  immoral  about  abandoning  your  own  judgement"
Cowards always run in  packs
Ishi did not become the arrow, I suspect. The arrow became Ishi.

Offline Pat B

  • Administrator
  • Member
  • Posts: 37,618
Re: Staining POC
« Reply #1 on: October 05, 2009, 01:02:12 pm »
I haven't bought POC for a few years but I never had a problem staining them. You might contact who you purchased them from for suggestions.
  Another option would be to use paint instead of stain. It goes on top and not into the wood. I have had good results with spray on Krylon paints and they come in many colors.
Logged
Make the most of all that comes and the least of all that goes!    Pat Brennan  Brevard, NC

Bluehawk

  • Guest
Re: Staining POC
« Reply #2 on: October 06, 2009, 11:11:09 am »
Sounds like  someone sealed them prior to you getting them   I have never had a problem staining POC  for 30 years .  Just stained some the other night   they were fine .   
Logged

Offline zeNBowyer

  • Member
  • Posts: 649
Re: Staining POC
« Reply #3 on: October 06, 2009, 06:11:09 pm »
I  sanded them  but the laquer  must  have  penetrated deeper  into  the  wood,  that  must  be  it,  thanx:)
Logged
"There's  something  immoral  about  abandoning  your  own  judgement"
Cowards always run in  packs
Ishi did not become the arrow, I suspect. The arrow became Ishi.

Offline Pat B

  • Administrator
  • Member
  • Posts: 37,618
Re: Staining POC
« Reply #4 on: October 06, 2009, 10:58:54 pm »
Did you get them from an individual or a company?
Logged
Make the most of all that comes and the least of all that goes!    Pat Brennan  Brevard, NC

Offline zeNBowyer

  • Member
  • Posts: 649
Re: Staining POC
« Reply #5 on: October 06, 2009, 11:17:08 pm »
I  got these  from  Rose  City,  and  I see  from their  website they  laquer  them,  perhaps   didn't sand e nough,  next time  I'll  be  smart  and  order  bare  wood:)
Logged
"There's  something  immoral  about  abandoning  your  own  judgement"
Cowards always run in  packs
Ishi did not become the arrow, I suspect. The arrow became Ishi.

Offline swimbill

  • Member
  • Posts: 79
Re: Staining POC
« Reply #6 on: October 07, 2009, 09:22:14 am »
If it is lacquer you can remove it pretty easily by using lacquer thinner and 0000 steel wool.  Wet the steel wool and rub down the arrow shaft. 
swimbill
Logged

Offline Tom Leemans

  • Member
  • Posts: 524
Re: Staining POC
« Reply #7 on: October 09, 2009, 12:52:10 pm »
Yeah I would steel wool them with thinner. If you sand too much it may affect spine. I use alcohol based stains from Larry Maggard. The same stuff is available from Mike Yancey at Pine Hollow longbows. A little goes a long way.
Logged

Offline hawkbow

  • Member
  • Posts: 2,051
    • High Country Archer
Re: Staining POC
« Reply #8 on: October 09, 2009, 03:24:38 pm »
I would just shoot them until it wears off.. LOL.. good luck brother.. Hawk
Logged
IT IS BETTER TO LOSE WITH HONOR. THAN TO WIN THROUGH DECEPTION...


Mike "Hawk" Huston

Offline zeNBowyer

  • Member
  • Posts: 649
Re: Staining POC
« Reply #9 on: October 09, 2009, 04:28:36 pm »
OK  thanx  all  for the  tips:)
Logged
"There's  something  immoral  about  abandoning  your  own  judgement"
Cowards always run in  packs
Ishi did not become the arrow, I suspect. The arrow became Ishi.
Pages: [1]
« previous next »